background image

page 10      TC42_B2 

230905-36

WALL TERMINATION VENTING

Exterior wall opening:

Determine the exact position of the fi replace so that the vent 
pipe is centred (if possible) between two building framing 
members. Consult your local building codes prior to proceed-
ing. The vent kit will accommodate up to a maximum wall 
thickness of 12 inches.

1)  Having determined the position of the fi replace, cut and 

frame a 14-1/2 inches opening centred at a minimum 
height of 74-1/4 inches above the fl oor. The opening may 
be round or square. Height of the opening will vary with 
each installation. As the horizontal vent run increases, so 
does the minimum vertical rise (see Fig. #17).

IMPORTANT:  When locating the opening, it should be 
noted that vent terminal clearances must be maintained. 
See "Vent Terminal Clearances" section for proper 
clearances.

A minimum 2 foot length of pipe is required for any wall ter-
mination. With this minimal vertical rise in combination with a 
90° elbow, a maximum horizontal run of 1

8

 inches is permitted 

(see Fig. #17 and 1

8

). For longer horizontal runs greater than 

1

8

 inches, increase vertical rise appropriately. The rise and 

run must be constrained to the boundaries of the chart shown 
in fi gure #17. The horizontal run of vent should have a 1/4" 
rise for every 1 ft. of run towards the termination.

HEARTH EXTENSION

While a hearth extension is not required 
for this fi replace, one is recommended for 
aesthetic reasons. The hearth extension 
should be noncombustible and must not 
be any more than 1" above the bottom of 
the fi replace. If thicker, fi replace must be 
raised up accordingly.

Caution:  Hearth extensions thicker than 
1" will interfere with the window frame.

1/4"

1"
MAX

WINDOW

FRAME

HEARTH

EXTENSION

WINDOW

TRACK

SUB-

FLOOR

Fig. # 13

VENTING

Before installing venting for this unit, the installer should read 
these instructions to insure that the proper vent confi guration 
has been selected.
Use only Town and Country Termination kits #:
 

TCVT.WTA - Wall Termination Kit

 

TCVT.RTA - Roof Termination Kit

Vent system components approved for use with the Town and 
Country Fireplace are shown in Figure #15. 

Various combinations of vertical and horizontal runs may be 
used. Refer to Figure # 17 and 1

8

 for details. For optimum 

performance and fl ame appearance, keep the vent length 
to a minimum and limit the number of elbows. Connections 
between each vent system component must be tightly joined, 
secured with sheet metal screws and sealed. A horizontal run 
of vent should have a 1/4" rise for every 1 ft. of run towards 
the termination.

CAUTION:  UNDER NO CONDITION SHOULD COMBUSTI-
BLE MATERIAL BE CLOSER THAN 1 3/4 INCHES FROM 
THE SIDES AND BOTTOM AND 1 3/4 INCHES FROM 
THE TOP OF A HORIZONTAL SECTIONS OF THE VENT 
PIPE AND 1 3/4 INCHES FROM A VERTICAL SECTION 
OF PIPE.

Содержание TC42 B Series





































Отзывы: