TANDBERG MCU Скачать руководство пользователя

Страница: 54 / 65

TANDBERG MCU

Configure the MCU

Software Upgrade

Software upgrade is where new software to the MCU can be installed. It also shows the current software version
and the MCU’s hardware serial number.

System Information

Software Version

Shows the currently installed Software version.

Hardware Serial Number

This unique identifier number for the MCU must be provided when ordering

Software Upgrade.

Installed Options

Shows the currently installed Options.

Current Option Key

Shows the current Option Key.

Software Option

New Option Key

Enter the option key in the Key field and press ‘Enable Option’. The system will

validate the key, and if valid a restart would be requested for the new option to
take effect.

Install Software

Release Key

Enter the release key in the Key field and press ‘Install Software’. You will be

presented with a new page where you select the software package file to upload.

UPGRADE

THE

MCU,

VALID

ELEASE

AND

OFTWARE

FILE

REQUIRED

ONTACT

YOUR

TANDBERG

REPRESENTATIVE

FOR

INFO

NOTE

Содержание MCU


































































Результаты поиска

Содержание MCU

Отзывы:

Похожие инструкции для MCU

Бренды по названию

Популярные бренды

TANDBERG MCU, Руководство пользователя

Результаты поиска

Содержание MCU

Отзывы:

Похожие инструкции для MCU

Бренды по названию

Популярные бренды