background image

                                                                                                       TX7322 Addressable Sounder Base 

 

 

        Installation & Operation Manual  

Fig.14 Tone setting              Fig.15 

Success to setting              Fig.16 Fail to setting 

 

3.5 Read Configuration     

Under the main menu,  as described in Section 3.2,  the  configuration parameters of the 

Addressable Sounder Base can be viewed by clicking the button 1“Read” or “1”, as shown in 

Figure 9. 

4 General Maintenance   

 

1.

 

Inform the suitable personnel before conducting the maintenance. 

2.

 

Disable the alarm warning device on the control panel to prevent false alarm. 

3.

 

Do  not attempt to repair the circuitry of the alarm warning device,  it may affect the 

operation to respond to a fire condition and will void the manufacturer’s warranty.  

4.

 

Use a damp cloth to clean the surface.  

5.

 

Notify again proper personnel after conducting the maintenance and make sure to enable 

the alarm warning device and confirm if up and running.  

6.

 

Perform the maintenance on semi-annually or depending on the site conditions.  

5 Troubleshooting Guide    

 

What you notice 

What it means 

What to do 

Address not enrolling 

In non-coding mode 

The wiring is loose 

The address is duplicate 

View the encoding mode 

Conduct maintenance 

Re-Commission the device 

Unable to commission 

The damage the electronic circuit 

Replace the device 

 

Appendix 1  

 
Operational Performance Data for LPCB Approved Tones 

 

1.

 

Tone 14 – Volume dB(A) 

Table 2 Sound pressure level of tone 14 at

 

different bus voltage with 3 meters away 

Angle 

(3m) 

Horizontal Plane 

Vertical Plane 

Max 28V 

Min 17.5V 

Max 28V 

Min 17.5V 

15° 

74.9 

68.9 

80.0 

73.5 

45° 

73.1 

73.1 

81.9 

73.2 

75° 

72.9 

70.2 

80.0 

79.5 

105° 

73.5 

71.5 

78.4 

75.7 

135° 

74.4 

71.8 

78.9 

78.6 

165° 

74.2 

70.8 

78.2 

71.7 

                                                                                                                               4050100446-Rev1.0-0917                                                                      

 

 

    TANDA UK  

                                                                                                                                           

Specifications are subject to change without prior notice 

10 

      

 

Содержание TX7322













Отзывы: