Tanco 580-J Скачать руководство пользователя | Manualshive

Страница: 27 / 44

background image

- 27 -

Tanco Autowrap 580-S/J

Operator’s manual

3.7

Film Break Alarm

Only operational where optional film break sensor is installed (see parts book).
If the film should break, after 1 second the display will show “STOP”, the alarm will sound and the turntable stops.
The film break alarm is only operational above a wrapping speed of 15rpm.

3.8

Total Reset

If for some reason the data in the instrument is corrupted or the display shows '

PrOg

' then the instrument must be

totally reset.
1.

Switch power off.

2.

Press and hold all 3 control switches.

3.

Switch power on.

4.

Release all switches.

All instrument settings should be returned to the factory-set values. If the display shows '

PrOg

' again, the instrument

may be faulty and must be returned to the manufacturer for inspection and repair.

3.9

Other CAL Mode Settings

Cut and Start Release duration

Switch the power on while pressing and holding the

button to enter Cal Mode 2.

Press the

button to select channel 2.

The default time is 3 seconds. Press /Hold the

button to change the setting.

Film Break Sensor

– On/Off

Enter Cal Mode 2 as above.

Press the

button to cycle to channel 3.

Press the

button to toggle on/off.

Issue 1: 19/12/02

Original issue based on UK332-1.DOC

«
...
25
26
27
28
29
...
»

Содержание 580-J













































Отзывы:

Нет отзывов

Похожие инструкции для 580-J

Бренд: KitchenAid Страницы: 7

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 19

Бренд: KitchenAid Страницы: 19

Бренд: KitchenAid Страницы: 3

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 1

Бренд: Amica Страницы: 16

Бренд: MTD Страницы: 20

Бренд: New Holland Страницы: 41

Бренд: New Holland Страницы: 41

Бренд: McCulloch Страницы: 108

Бренд: Yanmar Страницы: 4

Бренд: Garbin Страницы: 69

Бренд: Jenn-Air Страницы: 28

Бренд: CAMSO Страницы: 29

Бренд: Original Tractor Cabs Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды