tams elektronik LD-G-3 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 23

tams elektronik LD-G-3 Скачать руководство пользователя страница 7

English

LD-G-3 / LD-W-3

Page 26

EMC declaration

This product is developed in accordance with the European standards
EN 55014 and EN 50082-1, tested corresponding to the EC - directive
89/336/EWG (EMVG of 09/11/1992, electromagnetic tolerance) and
meets legal requirements. To guarantee the electromagnetic tolerance
you must take the following precautions:

§

Connect the transformer only to an approved mains socket installed
by an authorised electrician.

§

Make no changes to the original parts and accurately follow the
instructions, print layout and circuit diagram included with this manual.

§

Use only original spare parts if you have to repair the module.

Operation overview

The decoder is designed for operation in Motorola I or II format and can
be adjusted to one of 255 adresses. It evaluates the digital data sent by
the central unit to its address and transmitts it to the locomotive.

Function speed level and direction of motion

The speed level set at the central unit and the change-direction
command are transmitted to the locomotive by the decoder. At a
direction change command, the current direction of travel is saved.

Velocity characteristics

By adjusting the starting and the maximum velocity an individual
velocity characteristic can be programmed via the central unit. The
adjustments set the actual motor voltage of the locomotive. The motor
voltage has an immediate effect on the driving speed of the locomotive
at a chosen speed level during the operation.
The operating voltage of the locomotive motor at speed level 1 is set by
adjusting the starting velocity. Normally the motor voltage is adjusted
so that the locomotive just starts to run at speed level 1.

«
...
5
6
7
8
9
...
»

Содержание LD-G-3
























Отзывы:

Нет отзывов