tams elektronik LD-G-3 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 23

tams elektronik LD-G-3 Скачать руководство пользователя страница 15

English

LD-G-3 / LD-W-3

Page 34

1. Programming the locomotive address

After accessing the programming mode enter the present or the new
locomotive address. It is not necessary to enter the old address if you
intend to enter a new locomotive address. Confirm the input by
switching on the function "function". The locomotive confirms the input
by flashing the front lamp once. Set the speed control knob to "0". To
access the following menu point, switch off the function "function".

2. Programming the starting velocity

Turn the speed control knob. As soon as the locomotive is running with
the starting velocity you want switch on the function "function". The
locomotive confirms the input by flashing the front lamp twice. Set the
speed control knob to "0". To access the following menu point, switch
off the function "function".

3. Programming the maximum velocity

Turn the speed control knob. As soon as the locomotive is running with
the maximum wanted velocity, switch on the the function "function".
The locomotive confirms the input by flashing the front lamp three
times. Set the speed control knob to "0". To access the following menu
point, switch off the function "function".

4. Programming the acceleration and brake delay

Operate the speed control knob. Now the locomotive accelerates and
brakes alternately. By setting a low speed level you obtain a fast
acceleration and brake delay, by setting a high speed level you obtain a
slow acceleration and brake delay. While accelerating the front lamp of
the locomtive is off, when braking it is on. Set the acceleration and
brake delay required and switch on the function "function". The
locomotive confirms the input by flashing the front lamp four times. Set
the speed level to "0" while the lamp flashes, otherwise the locomotive
will run with this speed level when the standard operation starts.
With that the programming is finished, the decoder automatically
switches to standard operation.

«
...
13
14
15
16
17
...
»

Содержание LD-G-3
























Отзывы:

Нет отзывов