Takara Bio SMARTer ICELL8 cx Скачать руководство пользователя | Manualshive

Страница: 7 / 35

background image

SMARTer™ ICELL8® cx Single-Cell System User Manual

(061918)

takarabio.com

Takara Bio USA, Inc.

Page 7 of 35

Certification and standards information:

The ICELL8 cx fulfills the following requirements: EN 61010-1:1993 + A2:1995/IEC 61010-1:1990
+ A1:1992 + A2:1995.

Safety specifications are also met under the following environmental conditions, which are in
addition to those stated in the operating conditions:

•

Installation Category (overvoltage category) II according to IEC 60664-1.

The

Installation Category defines the level of transient overvoltage which the instrument is
designed to withstand safely. It depends on the nature of the electricity supply and its means
of overvoltage protection. For example, in CAT II, which is the category typically used for
instruments in hospital, research, and industrial laboratories, the expected transient
overvoltage is 2,500 V for a 230-V supply and 1,500 V for a 120-V supply.

•

Pollution Degree 2 according to IEC 60664-1.

Pollution Degree 2 assumes that normally

only nonconductive pollution (e.g., dust) are present in the operating environment, with the
exception of occasional conductivity caused by condensation.

Both the Installation Category (overvoltage category) and the Pollution Degree affect the
dimensioning of electrical insulation within the instrument.

Ethernet power
cord

«
...
5
6
7
8
9
...
»

Содержание SMARTer ICELL8 cx




































Отзывы:

Нет отзывов

Похожие инструкции для SMARTer ICELL8 cx

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: Taber Страницы: 27

Бренд: Landoll Страницы: 83

ActiveFinder One

Бренд: LaserLiner Страницы: 92

Бренд: ubicquia Страницы: 36

AirForm Night Splint

Бренд: Össur Страницы: 16

Бренд: Össur Страницы: 17

Pendalyte 40472U

Бренд: Lightolier Страницы: 3

Бренд: SAC Страницы: 2

Бренд: Hella Gutmann Страницы: 48

Бренд: Zafferano Страницы: 28

Бренд: Basler Страницы: 33

DynaTrap DT1260-TUN

Бренд: Dynamic Страницы: 4

Бренд: Elma Страницы: 35

Бренд: Qtx Страницы: 6

Бренд: Jäger Страницы: 36

Бренд: IMG STAGE LINE Страницы: 12

TRACER pH PockeTester 1741

Бренд: LaMotte Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды