manualshive.com logo in svg

TACKLIFE DP0813W, Руководство пользователя, Страница: 9 / 22

Поделиться
Скачать
TACKLIFE DP0813W Скачать руководство пользователя страница 9

ASSEMBLY & ADJUSTMENTS

UNPACKING

With the help of a friend or trustworthy foe, carefully remove the drill press from the packaging. Make

sure to take out all contents and accessories. Do not discard the packaging until the drill press is com-

pletely assembled.

Before using the drill press, you must assemble the unit using the instructions in this section. Check

your packing list against the diagram below. If any part is damaged or missing, please contact our

customer service, email us at [email protected].

PACKING LIST

A.

Head/Motor Assembly (1)

B.

Base (1)

C.

Table Assembly (1)

D.

Column Assembly (1)

E.

Hex Head Bolts (3)

F.

Hex Wrench (2)

G.

Chuck (1)

H.

Belt Tension Lever (1)

I.Chuck Key (1)

J.Feed Handles (3)

The tools listed below are not included but are required for either assembly or adjustment.

● Adjustable wrench

● Hammer and block of wood, or rubber mallet, or dead-blow hammer

A

B

C

D

G

H

I

J

WARNING:

Do not plug in or turn on the tool until it is fully assembled according to the instruc-

tions. Failure to follow the safety instructions may result in serious personal injury.

WARNING:

Do not plug in or turn on the tool until it is fully assembled according on the instruc-

tions. Failure to follow the safety instructions may result in serious personal injury.

REMOVING THE ANTI-RUST GREASE

To protect the drill press from moisture, a protective coating has been applied to the machine’s sur-

faces. Follow the directions below to remove the coating.

1. Remove the excess oil and grease by wiping it off with a clean cloth.

2. Remove any residue from the exposed surfaces with a rag moistened with acetone, kerosene, or

other removal agent. Wear gloves to protect your skin. Do not use gasoline, or cellulose-based sol-

vents such as paint thinner or lacquer thinner, as these will damage the paintedsurfaces.

3. Apply a light coat of good-quality paste wax to the table and column to guard against rust and cor-

rosion.

- 08 -

F

E

Содержание DP0813W























Отзывы:

Нет отзывов