SystemAir HHFlex Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 16

SystemAir HHFlex Скачать руководство пользователя страница 9

5. STACKED CASING SECTIONS

5.1 - Unit without intermediate base frame (equal
width)

Fig. 26 - Unit without intermediate base frame

Indoor installation
•

Position the casing sections on top of one another
so that the corner posts are in the same plane.

•

Mount the profiles supplied as described below.
For sections of equal length, these profiles should
be mounted all round the unit.

•

For shorter or longer upper sections the ends need
no further finish.

Fig. 27 - Mounting profile, indoor location, unit

without intermediate base frame

Outdoor installation
•

Position the casing sections on top of one another
so that the corner posts are in the same plane.

•

Mount the profiles supplied as described below. For
sections of equal length, mount the profiles all
round the unit.

Fig. 28 - Mounting profile, outdoor location, unit

without intermediate base frame

•

If the top section is shorter than the bottom
section, the ends should be finished as described
below.

Fig. 29 - Unit with shorter top section without

intermediate base frame

HHFlex Air Handling Units

| 9

«
...
7
8
9
10
11
...
»

Содержание HHFlex

















Отзывы:

Нет отзывов