SystemAir HHFlex Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 16

SystemAir HHFlex Скачать руководство пользователя страница 10

Fig. 30 - Roof finish, unit with shorter top section

without intermediate base frame

•

A longer top section needs no further finish at the
ends.

Fig. 31 - Unit with longer top section without

intermediate base frame

NOTE: For outdoor installation seal all jonts resulting
from the mounted profiles. This applies to both corner
and butt joints.

5.2 - Unit with intermediate base frame (equal
width)

Fig. 32 - Unit with intermediate base frame

Indoor installation
For indoor installation connection profiles of 240 mm
length are supplied.
•

Position the casings on top of one another so that
the corner posts are in the same plane. The base
frame of the top section should be slightly back
compared to the bottom casing section.

If stacking units in an indoor installation the connection
profiles should be placed between the different unit
sections. Use the following assembly method:
•

Install a connection profile to the end of the casing
section, stopping at the module line (A).

•

Install a connection profile at the joint (B)

•

Install a connection profile against adjacent section
(C)

Fig. 33 - Stacking, indoor location with

intermediate base frame

Fig. 34 - Fixing profile, indoor location with

intermediate base frame

max 960 mm

240

mm

A

B

C

10 |

HHFlex Air Handling Units

«
...
8
9
10
11
12
...
»

Содержание HHFlex

















Отзывы:

Нет отзывов