background image

THREE-YEAR LIMITED WARRANTY

System Sensor warrants its enclosed product to be free from defects in materials and 
workmanship under normal use and service for a period of three years from date of 
manufacture. System Sensor makes no other express warranty for the enclosed product. 
No agent, representative, dealer, or employee of the Company has the authority to in-
crease or alter the obligations or limitations of this Warranty. The Company’s obligation 
of this Warranty shall be limited to the replacement of any part of the product which is 
found to be defective in materials or workmanship under normal use and service during 
the three year period commencing with the date of manufacture. After phoning System 
Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return Authorization number, 
send defective units postage prepaid to: Honeywell, 12220 Rojas Drive, Suite 700, El Paso 

TX 79936, USA. Please include a note describing the malfunction and suspected cause 
of failure. The Company shall not be obligated to replace units which are found to be 
defective because of damage, unreasonable use, modifications, or alterations occurring 
after the date of manufacture. In no case shall the Company be liable for any consequen-
tial or incidental damages for breach of this or any other Warranty, expressed or implied 
whatsoever, even if the loss or damage is caused by the Company’s negligence or fault. 
Some states do not allow the exclusion or limitation of incidental or consequential dam-
ages, so the above limitation or exclusion may not apply to you. This Warranty gives you 
specific legal rights, and you may also have other rights which vary from state to state.

Please refer to insert for the Limitations of Fire Alarm Systems

  8 

I56-4260-002R 

  

©2016 System Sensor. 06-10

Содержание DUCTSD240









Отзывы: