manualshive.com logo in svg

Symetrix 610, Руководство пользователя, Страница: 20 / 22

Поделиться
Скачать
Symetrix 610 Скачать руководство пользователя страница 20

Page 18

COUGH

DUMP PROFANITY

START DELAY

EXIT DELAY

Default configuration programming procedure

The 610 default configuration is set from the front panel. The process involves placing the 610 in

programming mode and selecting one of six possible configurations. It is not necessary to remove

the unit from the equipment rack, or to remove the top cover to configure or re-configure. The

unit must be powered up and not in use. 

Please note - the 610 cannot be configured while opera-

tional!

The configuration settings are nonvolatile. Should power go down, the last configuration setting

is maintained. To program the 610 default configuration, proceed as follows:

Step #1 - Place 610 in BYPASS mode - 

Use the STATUS button at the left end of the 610 front

panel to place the 610 in BYPASS mode.

Step #2

 -  

Initiate Programming Mode

 - Press all four front panel lighted push buttons (EXIT

DELAY, START DELAY, COUGH, DUMP PROFANITY) and hold until all four lights come on

(approximately five seconds). When you release the buttons all four will flash, indicating that the

610 is in programming mode.

X

X                     X

   X

Step #3

 - 

Select Desired Option 

- While all four lights continue to flash, select your option by

pressing a button or combination of buttons as indicated in the table on the following page. The

associated light(s) flash to confirm your selection. After several seconds the light(s) will stop

flashing, indicating that the 610 has left the programming mode.

Step #4 - Return 610 to OPERATE mode 

- Use the STATUS button at the left end of the 610

front panel to place the 610 in OPERATE mode. The unit is now ready to operate.

Содержание 610























Отзывы:

Нет отзывов