background image

12

ARTÙ 2

Air circulation

It is vital that areas where gas devices are installed (type B) have 

access to the amount of air necessary for the regular combustion 

of gas as well as the ventilation of the venue.

-  It is prohibited to use an extractor fan, fireplaces and other similar 

devices at the same time as the water heater.

-  The area where the water heater is installed must have a regular 

flow of air for ventilation.

Air flow

The flow of air must occur by the following means:

-  permanent openings in the wall that lead outdoors;

-  single or collective ventilation ducts.

The air used for ventilation must be taken directly from an outside 

location, that is far from sources of pollution.

Indirect ventilation from adjacent areas are permitted with the 

following limitations:

-  the adjacent area is equipped with direct ventilation;

-  the devices within the area to ventilate are connected to a waste 

duct;

-  the adjacent area does not contain a bedroom and is not a 

common area;

-  the adjacent area is not a fire hazard such as a storage area for 

flammable materials, garage etc.;

-  the adjacent area is not lower than the area to ventilate as this 

might lead to an opposing draught (this can be caused by other 

devices that operate on the basis of combustion, a fireplace or any 

suction device that have not been given an adequate air supply);

-  the air flow from the adjacent area occurs freely through 

permanent openings.

2.d Electrical connection to battery

The device is powered by two 1,5 V batteries (D-Type model) alkaline 

long lasting model, thus it is not necessary to connect the device to a

power socket.

fig. 5

CARD CONNECTION

1 Display

2a 

SV1 (Pilot solenoid valve)

2b 

SV2 (Burner solenoid valve)

Detection electrode

Pilot burner

Ignition electrode

Flue gas thermostat (100 °C)

Limit thermostat (85 °C)

Batteries box

Electronic control board

10 

ON-OFF micro-switch

11 

Water micro-switch

12 

NTC probe

2.e Gas connection

See paragraph 2.a.

Determine the pipe diameter according to current regulations. Before 

installing the device blow in the gas pipe to eliminate any residue 

from its manufacturing. Connect the water heater to the internal 

system’s gas pipes and place a tap above the device for the halting 

and release of gas.

The water heaters that are powered by tanks of L.P.G. gas with 

regulation and interception devices, must be connected correctly 

so to guarantee the safety of persons and the surrounding area. 

Follow all related regulations.

When initially installing the device qualified persons must perform 

the following tests: 

-  check that the internal and external parts of the gas supplying 

device are sealed;

-  check that the gas quantity supplied is equal to that required by 

the device; 

-  check that the device receives the type of gas it is manufactured 

to process;

-  check that the gas supply pressure does not go beyond the 

maximum pressure values displayed on the information plate; 

-  check that the gas supply system supplies the necessary amount 

of gas to the device and that it is equipped with all the necessary 

safety devices prescribed by current regulations.

If the user is absent for a lengthy period, turn off the main gas 

supply tap. 

Do not obstruct the area’s ventilation openings where the device is 

installed to avoid dangers such as the build up of toxic and explosive 

substances.

Do not utilize gas tubes to earth electrical devices.

2.f Water connection

Connect the water heater to the water supply and insert a tap to 

intercept the water above the device. From the front, the cold water 

input is on the right and the hot water output is on the left.

  Remove the protective caps from the inlet and outlet water 

connection. 

Ensure that the tubes of you water system are not used to earth your 

electrical system or telephone, 

they are absolutely inappropriate 

for performing this task

.

In a short amount of time this can damage tubes and the device.

fig. 6

1  Release hood

2  Flue gas safety device

3  Water limit thermostat

4  Heat exchanger

5 Burner

6  Detection electrode

7  Pilot burner

8  Ignition electrode

9 Injector

10  Hot water outlet

11  Pressure intake

12  Temperature selector

13 Venturi

14  Hydraulic valve

15  Water filter

16 Membrane

17  Cold water inlet

18 Economiser

19  Gas valve

20  Safety device

21  Gas filter

22 Battery

23  Electrical card

24  Micro switch

WATER CIRCUIT

2.g Disposal of waste product

This 

B

11BS

 water heater is supplied with a device for releasing flue 

gas.

For output of combustion by-products refer to the regulations in 

force including any updates. See paragraph 2.a.

The gas devices with an attachment for a waste gas flue must be 

connected directly to properly working chimney or flue pipe; only if 

these devices are not present is it then permitted to release gases 

directly outside. The fitting of devices to a chimney or flue pipe must 

occur via a smoke channel. Smoke channels must be connected to a 

chimney or a smoke channel in the same or adjacent area to where 

the device is installed and must be made of materials resistant to 

mechanical strain, heat and the effects of combustion by-products 

and their condensation. The flue gas temperature must always be 

above condensation temperature in all points of the smoke channel 

regardless of external conditions.

FLUE GAS RELEASE SAFETY DEVICE

The product is equipped with a series of flue gas release safety 

devices. The device ensures the correct release of combustion 

byproducts; the flow of combustible gas to the release conduit and 

the smoke channel.

The safety device contains a “

thermostat

” connected to the 

electronic devices, it can stop the flow of gas to the main burner or 

to the pilot flame. The safety device can be triggered by the partial 

or total obstruction of the release conduit or the smoke channel.

Содержание Artu 2 11

































Отзывы: