Swisher E4-U3005 PowerBroom Скачать руководство пользователя

Страница: 11 / 12

Troubleshooting Guide

Engine idle too high.
Broken clutch spring or worn clutch

spring boss.

Loose attachment holder.

Warped or damaged attachment.

Loose gearcase.

Drums rotates at engine

idle.

Excessive vibration.

Drums will not rotate.

Set idle: 2,750 (±250) min-1.
Replace spring/shoes as required,

check idle speed.

Inspect and re-tighten holders securely.

Inspect and replace attachment as

required.

Tighten gearcase securely.

Bent main shaft/worn or damaged

bushings.

Shaft not installed in powerhead or

gearcase.

Broken shaft.
Damaged gearcase.

Inspect and replace as necessary.

Inspect and reinstall as required.

Consult with a authorized

servicing dealer.

ADDITIONAL PROBLEMS

What To Check

Possible Cause

Remedy

Содержание E4-U3005 PowerBroom













Результаты поиска

Содержание E4-U3005 PowerBroom

Отзывы:

Похожие инструкции для E4-U3005 PowerBroom

Бренды по названию

Популярные бренды

Swisher E4-U3005 PowerBroom, Руководство оператора

Результаты поиска

Содержание E4-U3005 PowerBroom

Отзывы:

Похожие инструкции для E4-U3005 PowerBroom

Бренды по названию

Популярные бренды