S A N1 63 - 3L r e v 3
外销三
COST CO
英法西产品说明书（出澳洲）-
4
SET-UP
Check the ground where the product will be set up for any sharp objects or debris. Do not install the product over
concrete or any hard surface.
Place the product on a soft level surface at least 2 m / 6.5 ft from any structure or obstruction such as a fence,
garage, and house; overhanging branches, laundry lines or electrical wires.
Ensure the play area is free from hazards such as furniture, walls, sharp objects, other hard surfaces, etc.
Set up the product away from any potential fire hazard.
Keep the blower (air pump) and power cord away from areas of water and moisture. If water contacts the blower (air
pump), unplug the blower (air pump) power cord. Do not operate until the blower (air pump) is completely dry.
Remove the product from the carry bag. If any, ensure the slide cover coming with the product stretches well from
top to end. Be sure to place as close to the power source as possible.
Stretch the inflation tube and attach it to the end of the blower (air pump). Ensure the inflation tube is securely
attached and in good condition. The inflation tube should be straight and untwisted. Reposition the blower (air pump)
if necessary.
Please follow the below steps:
Note the number on the sprayer nozzle, and affix the sprayer nozzle to the corresponding number of hook & loop
fastener on the product. (Refer to pictures A, B) Attach the hose to water supply, turn on the water supply when the
product is fully inflated. (Refer to pictures C, D)
Push ground stakes through blower(air pump) base holes. You may need to use a hammer for proper placement.
Make sure the blower (air pump) power switch is in the OFF position. Ensure the power connections are safely sited
and tripping hazard is minimized.
Place the inflation tube onto the blower(air pump) and place the long end of the strap through the loops. Wrap the
strap around the inflation tube and feed it through the black loop. (Refer to picture E) Pull the strap tightly and secure
the reverse side to the black loop and affix it to the hook & loop fastener. Adjusting the direction of the inflation tube
to prevent bends or distortion that may impede the flow of air. (Refer to picture F)
The blower (air pump) should be securely sited and affixed to the ground before use. Plug the blower (air pump) into
an approved grounded outlet.
Ensure the blower (air pump) is free from debris and securely sited to avoid tripping.
Turn the blower (air pump) power switch to ON. The continual air-flow blower (air pump) must be left ON at all time
while the product is being used. (Refer to picture G)
The product should be fully inflated.
Ground support stakes are used for lawn ground surfaces. Hook and fit each provided ground stake through each
loop in the bouncer. To prevent overturn or lift during playing, push stakes firmly into the soil. Make sure the hooked
end of the stake is over the loop. The stakes should be placed level with or under the ground in order to reduce
tripping hazards. (Refer to picture H)
Please check the age recommendation and user weights (printed on the product). You must not exceed the total
weight for the product.
Make sure the water slide is fully inflated before children enter to play.
Hint: Air leak from the seams is necessary because the product is inflated by constant air flow and this leakage is
required to stop the product becoming over-inflated.
Hint: It is drawn user’s attention to the orientation of the inflatable equipment installation in relation to the sun. The
sliding surface of the product shall not face to the sun as sunshine can glare the children’s eyes when they are
sliding down along the slide.
2
C
D
E
E
F
H
G
1
1
1
1
A
3
3
3
3
hook & loop
fastener
B
Содержание happy hop
Страница 1: ...SAN163 3L rev3...
