SVERO Smart Hoist 22 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 16

background image

Svero Lifting AB | Momarken 19, 556 50 Jönköping, Sweden

T:

+46 (0) 36 31 65 70

8

Pic. 10 Fasten the stop screw lightly with a 4 mm Allen key

4.

Fasten the small cover plate on the Holder using a 2,5 mm Allen key.

Pic. 11 Fixing cover plate

5.

Position the side of the Smart Hoist with the hoisting unit fixed to it, on the beam
and mount the side plate with cover (Pos. 2) on to the other end of the suspension
bolt (Pos. 3). Slide this side plate against the lower flange of the beam and center
the Holder (Pos. 4 on Pic. 3) under the beam (Pic. 12). The distance between the
flange of the wheels on the side plates and the lower flange of the beam shall be
1 - 2 mm on each side.

«
...
6
7
8
9
10
...
»

Содержание Smart Hoist 22

















Отзывы:

Нет отзывов

Похожие инструкции для Smart Hoist 22

Бренд: Toku Страницы: 37

Бренд: Dolmar Страницы: 48

Бренд: Yale Страницы: 20

Бренд: Yale HOISTS Страницы: 166

Бренд: Yale HOISTS Страницы: 36

Бренд: Parkside Страницы: 72

Бренд: Nitchi Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды