SVERO Smart Hoist 22 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 16

background image

Svero Lifting AB | Momarken 19, 556 50 Jönköping, Sweden

T:

+46 (0) 36 31 65 70

5

Pic. 1 Side Plate with hoisting unit fixed in a cover

Pic. 2 Side Plate with cover

Pic. 3 Suspension Bolt with Holder mounted (left), and from below with conical cuts, stop
screws and 4 mm Allen key (right)

1.

The Smart Hoist is prepared for a 120 mm beam at delivery. If it will be used on a
wider beam add the relevant spacers and the right length of screw for each side-
plate, according to table 1 below. Spacers and screws are supplied in marked
plastic kit-bags, one for each beam width, together with Allen keys.

«
...
3
4
5
6
7
...
»

Содержание Smart Hoist 22

















Отзывы:

Нет отзывов

Похожие инструкции для Smart Hoist 22

Бренд: AMH Страницы: 19

Бренд: Budgit Страницы: 12

Бренд: Yale Страницы: 20

Бренд: ACCO Brands Страницы: 14

Бренд: HADEF Страницы: 10

Бренд: J. D. NEUHAUS Страницы: 64

Бренд: Ingersoll-Rand Страницы: 40

Бренд: HERKULES Страницы: 224

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды