manualshive.com logo in svg

Suzuki SMD12, Руководство оператора


Поделиться
Скачать
background image

1.  SYSTEM INTRODUCTION

1-37

1.18.2

How to create the local wireless network

Note 1: 

Do the procedure with [Local Network] in [Wireless LAN Settings] turned off.

Note 2: 

It may not be possible to connect to a local network if the network is unstable. 

In this case, turn [Wireless] off and on. Connect via existing LAN network.

Note 3: 

Confirm that [When Necessary] is selected in [Connect to the Internet] before 

doing the procedure.

1. Open the home screen, then tap [Settings]

[General]

[Wireless LAN Set-

tings]

[Wireless Mode].

2. Tap [Create Local Network], then tap "<" to go back one layer.

3. Tap [Name].
4. Enter the name of the network, then tap [

].

5. Tap [Password].
6. Enter the password, then tap [

]. (If the password is wrong, an error message ap-

pears. Tap the [OK] button then reenter the password.)

7. Turn on [Local Network] in [Wireless LAN Settings] to connect to the network.
8. Tap X on the title bar to close the menu.
9. Connect to Multi-Function Display at your tablet or smartphone.

Name TZTL15F

Password                                    XXXXXXXX

SMD12

Содержание SMD12



















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SMD12

NEC 1525M Manual preview
1525M
Бренд: NEC Страницы: 33
NEC MultiSync LCD2690WUXi Specification preview
MultiSync LCD2690WUXi
Бренд: NEC Страницы: 4
NEC 42XP10 - PlasmaSync - 42" Plasma Panel Specifications preview
42XP10 - PlasmaSync - 42" Plasma Panel
Бренд: NEC Страницы: 2
NEC AccuSync AS242W Setup Manual preview
AccuSync AS242W
Бренд: NEC Страницы: 2
NEC E421 User Manual preview
E421
Бренд: NEC Страницы: 70
A&D UB-511 Instruction Manual preview
UB-511
Бренд: A&D Страницы: 16
A&D UB-510 Operational Manual preview
UB-510
Бренд: A&D Страницы: 50
A&D UA-852 Manuale Di Istruzioni preview
UA-852
Бренд: A&D Страницы: 20
A&D UA-767 Manuel D'Instructions preview
UA-767
Бренд: A&D Страницы: 14
A&D UA-705 Quick Start Card preview
UA-705
Бренд: A&D Страницы: 3
A&D UA-621 Operation Manual preview
UA-621
Бренд: A&D Страницы: 42
A&D UA-1030T Specification preview
UA-1030T
Бренд: A&D Страницы: 2
A&D ESSENTIAL UB-525 Instruction Manual preview
ESSENTIAL UB-525
Бренд: A&D Страницы: 48
Raymarine A Series A50 User'S Reference Manual preview
A Series A50
Бренд: Raymarine Страницы: 154
Acer CBA272 User Manual preview
CBA272
Бренд: Acer Страницы: 114
Acer BX320HK Quick Manual preview
BX320HK
Бренд: Acer Страницы: 4
NEC MultiSync EA245WMi-BK User Manual preview
MultiSync EA245WMi-BK
Бренд: NEC Страницы: 30
AG Neovo CD-2201 User Manual preview
CD-2201
Бренд: AG Neovo Страницы: 33

Бренды по названию

Популярные бренды

Загрузить еще бренды