manualshive.com logo in svg

Suzuki SMD12, Руководство оператора


Поделиться
Скачать
background image

3.  PLOTTER

3-17

3.10.8

Alarms list

When an alarm is violated, you can see the name of the offending alarm on the 
[Alarms] list. The list stores both warning and system messages. Open the home 
screen, then tap [Lists] followed by [Alarms]. Active alarms are flashing and have a red 
vertical bar at the let margin. Tap an active alarm to acknowledge it and stop the flash-
ing. After the cause of an alarm is removed, the alarm message is moved to [HISTOR-
IC] section. Tap the close button to close the list.

3.11

Track

The track (or movement) of your ship is 
plotted on the screen with position data 
fed from the internal GPS navigator. Your 
track lets you see how your ship has 
moved over time.

The track is saved to the internal memory if track recording is activated. A line runs 
between each track point. The internal memory stores a maximum of 30,000 track 
points.

Track is saved when the power is turned off. Unnecessary track can be deleted. Track 
can also be used to create a route.

3.11.1

How to start, stop recording the track

Start recording

Open the slide-out menu or tap the boat icon, then turn [Track] on.

Stop recording

Method 1

: Tap the track, then tap [Stop Track].

Method 2

: Open the slide-out menu or tap the boat icon, then turn [Track] off.

3.11.2

How to show or hide the track display

Open the [Layers] menu and turn [Tracks] on or off.

Depth Alarm

Color on Status bar

Message

Date, time alarm generated

Track

Содержание SMD12



















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SMD12

Samsung QM85F Quick Setup Manual preview
QM85F
Бренд: Samsung Страницы: 2
Raymarine i70 Quick Reference preview
i70
Бренд: Raymarine Страницы: 12
Samsung SH37F Quick Setup Manual preview
SH37F
Бренд: Samsung Страницы: 2
Samsung DC32E Quick Setup Manual preview
DC32E
Бренд: Samsung Страницы: 2
Samsung ED65E User Manual preview
ED65E
Бренд: Samsung Страницы: 148
Raymarine A Series A50 User'S Reference Manual preview
A Series A50
Бренд: Raymarine Страницы: 154
uebe visomat comfort 20/40 Instructions For Use Manual preview
visomat comfort 20/40
Бренд: uebe Страницы: 33
uAvionix AV-30-C Instructions For Continued Airworthiness preview
AV-30-C
Бренд: uAvionix Страницы: 22
Vision ZL 7261 CL-5 Operation Manual preview
ZL 7261 CL-5
Бренд: Vision Страницы: 3
2E D2621W User Manual preview
D2621W
Бренд: 2E Страницы: 31
Uniden BW4151 Owner'S Manual preview
BW4151
Бренд: Uniden Страницы: 24
Barco Coronic Uniti User Manual preview
Coronic Uniti
Бренд: Barco Страницы: 74
ViewSonic VG500-2 Service Manual preview
VG500-2
Бренд: ViewSonic Страницы: 56
I-Inc iH-232HPB Specifications preview
iH-232HPB
Бренд: I-Inc Страницы: 1
Postium OBM-U090 User Manual preview
OBM-U090
Бренд: Postium Страницы: 44
Neway CL7677 User Manual preview
CL7677
Бренд: Neway Страницы: 13
Harris CMN-41 Installation And Operation Handbook preview
CMN-41
Бренд: Harris Страницы: 168
NEC NEC MultiSync FE950+ FE950+ FE950+ User Manual preview
NEC MultiSync FE950+ FE950+ FE950+
Бренд: NEC Страницы: 64

Бренды по названию

Популярные бренды

Загрузить еще бренды