manualshive.com logo in svg

Suzuki SMD12, Руководство оператора


Поделиться
Скачать
background image

14.  OTHER FUNCTIONS

14-5

INSTRUMENTS SETUP section

[Engine & Tank Automatic Setup]

: The system will automatically detect engines and 

tanks connected to the same network. This is the recommended method for setting up 
engines and tanks.

[Engine & Tank Manual Setup]:

Graphic Instruments Setup

:

[Graphic Instruments Setup] - [Maximum Boat Speed], [Maximum Wind Speed]

[Graphic Instruments Setup] - [Depth]

[Graphic Instruments Setup] - [Sea Surface Temperature]

Menu item

Description

Options (setting range)

[Engine & Tank 
Automatic Setup]

See "Engine & Tank Automatic Setup" below.

[Engine & Tank 
Manual Setup]

See "Engine & Tank Automatic Setup" on the next page.

[Graphic Instruments 
Setup]

See "Graphic Instruments Setup" below.

Menu Item

Description

Options (setting range)

[Nickname]

Change the nickname for the engine or tank.

[Used For Propulsion]

Select which engine/tank is used to 
calculate the distance which may be 
traveled using the remaining fuel. [ON] uses 
the engine/tank for calculations, [OFF] 
ignores the engine/tank.

[ON], [OFF]

[Reset] 

Resets the engine/tank details to default

[OK], [Cancel]

Menu Item

Description

Options (setting range)

[Maximum Boat Speed]

Set the transducer’s maximum detectable 
speed.

1 kn to 99 kn

[Maximum Wind Speed]

Set the transducer’s maximum detectable 
speed.

1 kn to 99 kn

Menu Item

Description

Options (setting range)

[Minimum Depth]

Set the transducer’s minimum detectable 
depth.

1 m to 19 m

[Maximum Depth]

Set the transducer’s maximum detectable 
depth.

20 m to 2000 m

Menu Item

Description

Options (setting range)

[Minimum Sea Surface 
Temperature]

Set the transducer’s minimum detectable 
temperature.

0.00°C to 99.99°C

[Maximum Sea Surface 
Temperature]

Set the transducer’s maximum detectable 
temperature.

0.01 to 99.99°C

Содержание SMD12



















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SMD12

NEC EA223WM-BK Setup Manual preview
EA223WM-BK
Бренд: NEC Страницы: 2
NEC MultiSync FP1375X Quick Start Manual preview
MultiSync FP1375X
Бренд: NEC Страницы: 16
I-Tech KKF1040B-TR User Manual preview
KKF1040B-TR
Бренд: I-Tech Страницы: 19
Avtek TouchScreen 55 User Manual preview
TouchScreen 55
Бренд: Avtek Страницы: 15
Radio Shack Life Wise User Manual preview
Life Wise
Бренд: Radio Shack Страницы: 2
Litemax Electronics LD1544 User Manual preview
LD1544
Бренд: Litemax Electronics Страницы: 12
IBM G 78 User Manual preview
G 78
Бренд: IBM Страницы: 22
Brookstone BKWIFICAMB User Manual preview
BKWIFICAMB
Бренд: Brookstone Страницы: 28
S&T kontron FlatView Series User Manual preview
kontron FlatView Series
Бренд: S&T Страницы: 65
AG Neovo EH-24 User Manual preview
EH-24
Бренд: AG Neovo Страницы: 32
G-Lab MD2230 Instruction Manual preview
MD2230
Бренд: G-Lab Страницы: 27
IEE PDK 0212-OWG13L Reference Manual preview
PDK 0212-OWG13L
Бренд: IEE Страницы: 10
Eizo FlexScan T761 Brochure & Specs preview
FlexScan T761
Бренд: Eizo Страницы: 2
3SIXT HEART RATE MONITOR STRAP User Manual preview
HEART RATE MONITOR STRAP
Бренд: 3SIXT Страницы: 6
Mastervolt CZone Touch 10 User Manual preview
CZone Touch 10
Бренд: Mastervolt Страницы: 33
i3TOUCH V-SENSE V8403 T10 User Manual preview
V-SENSE V8403 T10
Бренд: i3TOUCH Страницы: 32
Synergy Global Technology LCDR6U17-02 User Manual preview
LCDR6U17-02
Бренд: Synergy Global Technology Страницы: 18
ViewSonic VG2227WM - 22" LCD Monitor (Romanian) User Manual preview
VG2227WM - 22" LCD Monitor
Бренд: ViewSonic Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды