Suzuki 2009 AN400 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 143

Suzuki 2009 AN400 Скачать руководство пользователя страница 43

ABS: 4E-1

Brake

ABS

Precautions

Precautions for ABS (AN400A/ZAK9)

B905H14500001

Refer to “Precautions for ABS (AN400A/ZAK9)” in
Section 00 (Page 00-1) and “Precautions for Electrical
Circuit Service” in Section 00 in related manual.

ABS Information (AN400A/ZAK9)

B905H14500002

WARNING

!

• Be sure to bleed air from the brake fluid

circuit when the brake is felt spongy or
when a brake relating part is replaced.

• Never ride the motorcycle before bleeding

the air.

• Be sure to route the brake hoses correctly.
• The ABS does not shorten the motorcycle’s braking

distance. When riding down slopes or on wet or
bumpy roads the braking distance is lengthened as
compared to a motorcycle without ABS. In addition,
braking distance increases more, when the road is
slippery.

• The ABS does not control slides which may occur

when braking while turning. As with a motorcycle that
does not have ABS, it is best not apply the brakes
while turning.

• The brake levers may move by themselves when they

are applied. This is not a malfunction.

• Only use the specified tires.

General Description

Wheel Speed Sensor Description (AN400A/ZAK9)

B905H14501001

Wheel speed sensor consists of wheel speed sensor (1) and sensor rotor (2).

Front

Rear

1

2

I905H1450001-01

1

2

I905H1450002-02

«
...
41
42
43
44
45
...
»

Содержание 2009 AN400
















































































































































Отзывы:

Нет отзывов