Suzuki 2009 AN400 Скачать руководство пользователя страница 25

Страница: 25 / 143

Fuel System: 1G-2

Fuel Pump Disassembly and Assembly (AN400/
A/ZAK9)

B905H11706018

Disassembly

1) Remove the fuel pump assembly.

Refer to “Fuel Pump Assembly Removal and
Installation” in related manual.

2) Remove the dust cover (1).

3) For the other procedure, refer to “Fuel Pump

Disassembly and Assembly” in related manual.

Assembly

Assemble the fuel pump assembly in the reverse order
of the disassembly.
Refer to “Fuel Pump Disassembly and Assembly” in
related manual.

Specifications

Tightening Torque Specifications

B905H11707002

NOTE
The specified tightening torque is described in the following.
“Fuel Pump Components (AN400/A/ZAK9)” (Page 1G-1)

Reference:

For the tightening torque of fastener not specified in this section, refer to “Tightening Torque List” in Section 0C in
related manual.

Special Tools and Equipment

Recommended Service Material

B905H11708003

NOTE
Required service material is also described in the following.
“Fuel Pump Components (AN400/A/ZAK9)” (Page 1G-1)

I905H1170002-01

Содержание 2009 AN400
















































































































































Результаты поиска

Содержание 2009 AN400

Отзывы:

Suzuki 2009 AN400, Дополнительное руководство по обслуживанию, Страница: 25 / 143

Результаты поиска

Содержание 2009 AN400

Отзывы: