Suzuki 2009 AN400 Скачать руководство пользователя страница 127

Страница: 127 / 143

Steering / Handlebar: 6B-2

Repair Instructions

Grip Heater Removal and Installation (AN400ZAK9)

B905H16206016

Removal

Refer to “Grip Heater Removal and Installation (AN400ZK7/K8)” in related manual.

Grip Heater Diagram

Installation

Refer to “Grip Heater Removal and Installation (AN400ZK7/K8)” in related manual.

Grip Heater Inspection (AN400ZAK9)

B905H16206017

1) Disconnect the grip heater lead wire couplers. Refer

to “Grip Heater Removal and Installation
(AN400ZK7/K8)” in related manual.

2) Measure the grip heater resistance between the lead

wires. If the resistance is not within the specified
value, replace the grip heater with a new one.

Special tool

: 09900–25008 (Multi circuit tester set)

Tester knob indication
Resistance (

Ω

)

Grip heater resistance
LH: 4.50 – 5.50

Ω

at 20

C (68

F) (B – B)

RH: 3.78 – 4.62

Ω

at 20

C (68

F) (B – B)

G/B

W/B

G/B

O/Y

W/B

O/Y

W/B

I905H1620002-01

I905H1620003-01

Содержание 2009 AN400
















































































































































Результаты поиска

Содержание 2009 AN400

Отзывы:

Suzuki 2009 AN400, Дополнительное руководство по обслуживанию, Страница: 127 / 143

Результаты поиска

Содержание 2009 AN400

Отзывы: