Sutter Instrument TRIO MPC-165 Series Скачать руководство пользователя | Manualshive

Страница: 32 / 60

background image

TRIO MPC-165 SERIES MICROMANIPULATOR SYSTEM OPERATION MANUAL – REV. 2.67K2 (20201130) (FW V2.62)

30

4.8

Travel Speed

The following table shows the travel speeds for supported devices using orthogonal move commands.

Table 4-4. Travel speeds.

Device

mm/sec or µm/ms

Single Axis

Dual Axis (x 1.4)

MP-865/M * micromanipulator

3

4.2

MP-285/M ** micromanipulator

5

7

* The same applies also to the MP-845[S]/M & MP-245/M (discontinued) micromanipulators.

** The same applies also to the 3DMS & MPC-78 stages, and SOM & MOM objective movers,

MP-265/M micromanipulator (discontinued).

4.9

Commands

4.9.1

Get Active Device & Firmware Version (‘K’) Command

This command is used to obtain the current-active device attached to the controller. The data

returned is four bytes, the first of which is the device number (1 (MANIPULATOR A) or 2
(MANIPULATOR B), followed by the major version number, minor version number, and the
completion indicator.

Table 4-5. Get Active Device & Firmware Version (‘K’) command.

Tx/-

Delay

/-Rx

Ver. Total

Bytes

Byte

Offset

(Len.)

Value

Alt-

key-

pad #

Ctrl-

char

ASCII

def./-

char.

Description

Dec. Hex.

Binary

Tx All

1

0

75 4B 0100 1011 0075

K

Command

Rx All

4

0

1

-

2

01

-

02

0000 0001

–

0000 0010

^A

-

^B

<SOH>

-

<STX>

Currently-active device (1 – 2
(A – B)).

1

Major version number (e.g., if

ver. = 2.62, then byte = 2)

2

Minor version number (e.g., if
ver. = 2.62, then byte = 62)

3

13 0D 0000 1101

^M <CR>

Completion indicator

NOTE: The device number returned by the ‘K’ command indicates the active device for

external commands only; it is completely independent of the manual A and B switch on the

front of the MPC-100 ROE/controller.

4.9.2

Change Active Device (‘I’) Command

This command is used to change the currently-active device attached to the controller. One
byte follows the command, consisting of a value of 1 (for Device A) or 2 (for Device B). Two

bytes are returned: The first contains the device specified as confirmation, followed by the
completion indicator.

«
...
30
31
32
33
34
...
»

Содержание TRIO MPC-165 Series





























































Отзывы:

Нет отзывов

Похожие инструкции для TRIO MPC-165 Series

Бренд: ABB Страницы: 50

Бренд: Datapath Страницы: 12

Бренд: IDTECK Страницы: 94

Бренд: jbc Страницы: 8

Бренд: Lab.gruppen Страницы: 2

Бренд: Rain Bird Страницы: 18

Бренд: Atari Страницы: 3

Бренд: Forcepoint Страницы: 15

Бренд: SMC Networks Страницы: 12

Бренд: Carel Страницы: 36

Lift Inverter L1000V

Бренд: YASKAWA Страницы: 282

Бренд: Planar Страницы: 162

Бренд: THK Страницы: 134

Enclosure ENCR-10

Бренд: suprema Страницы: 18

Бренд: Zonex Страницы: 16

Бренд: SUPMEA Страницы: 32

Бренд: National Instruments Страницы: 20

Бренд: Eliweli Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды