Sutter Instrument TRIO MPC-165 Series Скачать руководство пользователя | Manualshive

Страница: 31 / 60

background image

TRIO MPC-165 SERIES MICROMANIPULATOR SYSTEM OPERATION MANUAL – REV. 2.67K2 (20201130) (FW V2.62)

29

4.6

Microsteps and Microns (Micrometers)

All coordinates sent to and received from the controller are in microsteps. To convert
between microsteps and microns (micrometers), use the following conversion factors
(multipliers):

Table 4-2. Microns/microsteps conversion

TRIO MPC-100 Controller with Device

From/To Units Conversion Factor

(multiplier)

MP-865/M* micromanipulator

µsteps



µm

0.09375

µm



µsteps

10.66666666667

MP-285/M** micromanipulator

µsteps



µm

0.125

µm



µsteps

8

* The same applies also to the MP-845[S]/M and MP-245/M (discontinued) with DB25 to

DB26HD adapter.
** The same applies also to the 3DMS or MT-78 stage, MOM or SOM objective mover, and

MP-265/M micromanipulator (discontinued).

For accuracy in your application, type these conversion factors as “double” (avoid using the

“float” type as it lacks precision with large values). When converting to microsteps, type the
result as a 32-bit “unsigned long” (C/C++), “uint32” (MATLAB), or “U32” (LabVIEW)

integer (positive only) value. When converting to microns, type the result as a “double”
(C/C++, MATLAB) or “DBL” (LabVIEW) 64-bit double-precision floating-point value.

4.7

Travel Ranges and Bounds

The following table shows the travel ranges and bounds for supported devices.

Table 4-3. Ranges and bounds

Device

Axis

Len.

(mm)

Origin

Microns

(Micrometers

(µm))

Microsteps

(µsteps)

MP-865/M micromanipulator

X

50

BOT

0 – 50,000

0 – 533,333

Y

12.5

BOT

0 – 12,500

0 – 133,333

Z

25

BOT

0 – 25,000

0 – 266,667

MP-845[S]/M * micromanipulator

X, Y, Z

25

BOT

0 – 25,000

0 – 266,667

MP-285/M** micromanipulator

X, Y, Z

25

BOT

0 – 25,000

0 – 200,000

* The

same applies also to the MP-245/M micromanipulator (discontinued) with DB25 to

DB26HD adapter.
** The same applies also to the 3DMS & MT-78 stages, and MOM & SOM objective movers,

and MP-265/M micromanipulator (discontinued) with 12.5mm for Y axis,
NOTE: Origin is a physical position of travel that defines the center of the absolute position

coordinate system (i.e., absolute position 0).

Physical Positions: BOT (Beginning Of Travel), COT (Center Of Travel), & EOT (End Of

Travel).

In the TRIO MPC-100, the Origin is fixed at BOT.
NOTE: Travel length of each axis is automatically determined by end-of-travel sensor.

«
...
29
30
31
32
33
...
»

Содержание TRIO MPC-165 Series





























































Отзывы:

Нет отзывов

Похожие инструкции для TRIO MPC-165 Series

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

Бренд: B&G Страницы: 19

Бренд: Lampert Страницы: 15

Бренд: Rabbit Страницы: 12

Бренд: YASKAWA Страницы: 92

MOVIFIT SC series

Бренд: SEW Страницы: 148

Бренд: Belimo Страницы: 2

Anafaze PPC-2000

Бренд: Watlow Страницы: 320

Бренд: MRC Страницы: 2

Бренд: Cytron Technologies Страницы: 20

TOCAhome 2 integra

Бренд: eKey Страницы: 56

Бренд: AUMA Страницы: 88

CNC-110A Series

Бренд: TAILY AUTOMATION Страницы: 15

Бренд: Invertek Страницы: 51

Бренд: Digilin Страницы: 8

Бренд: Visonic Networks Страницы: 4

Бренд: Rain Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды