background image

2. When inspection is needed, it should be carried out in a safe place and pay close attention 
to the surrounding environment.
3.If  there  is  any  abnormality  during  the  inspection,  please  rectify  the  abnormality  before 
riding. If the problem is difficult for you to solve, please contact Surron or the local authorized 
dealer.

      CAUTION 
1. The front and rear brakes are disc brakes. When the brake pads are worn severely, please 
replace them as soon as possible.
2. Keep the disc brake system clean in daily basis use and  avoid long-term adhesion of 
sediment, especially oil pollution.

Check Operational Unit 
1. Check if the suspension is bent, deformed, or damaged.
Check if the front fork is damaged, loose or oil leakage and other faults. Shake the handlebars 
up and down to check whether there is any abnormal sound caused by the front fork fault. If 
the front fork is malfunctioned, please contact Surron or the local authorized dealer.
2. Check Brakes 
Check if the free space of the brake lever is within the specified range (15-30mm). Adjust If it 
does not meet the requirements after measurement.
3.Check if the brakes function well. Please ride at low speed on dry flat road for inspection, 
and use the front and rear brakes respectively to check their braking effective.
4. Check Tires
The  tires  will  be  damaged  by  glass,  stones  and  other  matter  on  the  ground.  Please  pay 
attention to the road condition when riding. Avoid riding in places where tires may be easily 
damaged.  In  addition,  you  should  often  check  if  the  tires  have  distinct  cracks  and  other 
damages.
1)Check the tire pressure with the tire pressure gauge when in the cooling condition.
2)Check if there are cracks, damages or abnormal wear.
3)Check if the spokes of the wheel are loose.
4)Check the tightness of the chain. Up and down 10-20mm.
5)Check the depth of tire grooves.
Check tire wear, groove depth. If wear reached 2/3 of the convex block, the tire should be 
replaced.  When  there  is  abnormal  sound  or  swing  in  the  tire,  please  contact  your  local 

authorized dealer for inspection and maintenance.
The pivot shaft nut locking torque should be 30 N·m, and the rear axle nut locking torque 
should be 40 N·m, The front axle screw locking torque depend on the front fork.

      CAUTION 
1.The belt tension has been adjusted before delivery. Please do not adjust it without permis-
sion.
2.Hold  the  brake  lever  tightly.  If  the  braking  performance  is  still  not  good,  check  the 
cleanness of the disc.
If the problem cannot be solved, please contact your local authorized dealer for inspection.

Check the Battery 
1. Check the Power
The  bike  is  powered  by  a  sealed  lithium-ion  battery.  The  battery  should  be  fully  charged 
before  the  inspection.  Use  a  multimeter  to  test  the  positive  and  negative  voltage  of  the 
discharge port, the normal full voltage should be between 67-67.2V.
2. Check Battery Appearance
Check if the battery’s upper and lower sealing caps and the lcd screen are damaged. It will 
cause    water  get  into  the  power  pack  if  the  sealing  is  damaged.  fai  Contact  the  local 
authorized dealer if the battery case or cap is damaged.

      CAUTION 
1. Before installing or removing the battery, please close the key switch and turn off the air 
circuit switch, and close the sealant cap of charging port.
2. If the battery cannot be put into the battery compartment, please take out the battery and 
check if the battery is stuck by other objects such as cable harness.
3. It is recommended that in winter the indoor temperature for battery storage should be 
above 0℃ (32°F) and the battery remaining capacity should be checked regularly.

Charging and Charger Usage 
1.When charging, you are required to use the OEM charger. Do not use third-party charger, it 
might damage the battery and cause serious injury. 
2. Check if the input voltage of the charger is same with the voltage of the power supply.  
3.When  the  battery  is  fully  charged,  the  charger  will  automatically  stop  charging.  Avoid 

25          

26

Troubleshooting

Item

1.The battery cable is loose
2.Throttle is loose or fall off

1.bike dash out protection

2.Temperature protection

3.power-off protection

4.The throttle is malfunctioned

Fault Cause

Troubleshooting Methods

Power On

Motor not 

working

Speed fail-

ure or low 

maximum 

speed

In  principle,  the  first  inspection  (also  known  as  the  first  maintenance)  can  be  done  at 
10-30km if ride normally. 
Check Parts
1. The tightness of the spokes on the rear wheel 
2. If there is a gap in the headset
3. Check the tightness of chain
4.Belt tightness inspection. (There may be some friction on the new belt, which can be waxed 
on both sides of the belt.)
5. Suspension adjustment. Check if there is oil leakage, and if the compression and rebound 
damping is in the correct position.(Note: During adjustment, do not turn the adjusting knob 
to the extreme position.)
6.Check the tightness of all screws on the handlebars.

WARNING:During  the  whole  maintenance  process,  the  bike 
cannot  be  powered  on,  which  means  you  cannot  do  mainte-
nance with the bike is powered on.

Extra attention should be paid to your safety during the inspection. 
1. Choose a wide, flat area to park your bike.

Maintenance Guidance 

connecting the charger to the power supply for a long time.
4. Users are prohibited to disassemble the battery, disassemble battery without permission 
may cause serious injury.
5. When the battery is under over-discharge protection, it needs to be re-activated. Please 
refer to P25 < Troubleshooting > for activation method.

Motor and Controller Usage and Maintenance
1. Check tightness of the motor screws regularly. 
2. Check the motor and controller insulation condition regularly. 
3. Check the fuse condition regularly.
4. Do not wade in deep water, it might affect the motor operation.
      CAUTION
When the temperature of the motor and the controller is too high or the battery capacity is too 
low, the bike will automatically reduce the power to protect the powertrain.

Replace Fuse
If the speedometer, horn, and headlight do not work after the air circuit switch and key switch 
are turned ON, the fuse may be melted. If the fuse needs to be replaced, please turn off the 
air circuit switch first. The operation method is as follows:
1. Open the battery compartment cap, turn off the air circuit switch, take out the battery, the 
fuse box can be seen in front of the air circuit switch, and open the fuse box. (the fuse box is 
wrapped with black insulation tape)
2.Replace the broken fuse with the auxiliary one.Close the fuse box,install the battery,and 
close the cover of the battery compartment.                                       

1. Check whether the cable is securely 

connected

2. The plug connection is stable

3. Reconnect and secure the terminal

4. Check the brake lever and brake switch

1. Restart the bike

2. Wait for the bike temperature to return 

to normal

3. Check whether the cables and plugs of 

the brake, tilt switch, and side stand 

switch are securely connected

4. Check whether the cable of the throttle 

is properly connected to the plug

1. Low tires pressure

2.The charger is malfunctioned

Insufficient 

range for 

one charge

After con-

necting the 

power sup-

ply, the 

charger 

did not 

work nor-

mally, and 

the battery 

capacity 

no display

1. The battery over discharge 

protection occurs because the 

battery has not been charged 

for a long time or improperly 

stored

1. Restart the bike

2. Wait for the bike temperature to return 

to normal

3. Check whether the cables and plugs of 

the brake, tilt switch, and side stand 

switch are securely connected

4. Check whether the cable of the throttle 

is properly connected to the plug

3.The motor cable is loose or 

disconnected

3.Improper brake pads adjust-

ment 
4. The battery is overuse or 

damaged 

5. More uphill, frequent accel-

eration and deceleration, 

heavy load

4.Brake lever cannot return to 

idle or malfunctioned 

Charger not 

working

1. Insert the plug or connector firmly to 

open the battery compartment cap

2. Open the battery compartment cap 

and connect the plug firmly

3. Activate the battery

1. Connect the plug to the charging port 

on battery first and then connect to the 

power supply, the indicator light of the 

charger blinks alternately red and green

2. unplug and re-connect the connector 

of the charger and the power supply 

once; The indicator of the charger rapidly 

blinks red for 20 seconds at a frequency 

of 0.5S

3. After 20 seconds, the red indicator 

light keeps on for 10 seconds. Within 10 

seconds, unplug and re-connector 

between the charger power supply once

4. The enforcement charging function of 

the charger starts, and the charger 

enters the normal charging process

Note: a. Do not remove or insert the AC 

plug for 20 seconds in Step 2. Otherwise, 

you need to start all over from Step 1. B. 

unplug and re-connect to the power 

supply process in Step 3 need to be done 

within 10 seconds after the red light is 

on. If not, restart from Step 1

2.The connector of the battery 

power cable is loose
3. The battery over discharge 

and need to be Reactivate

1.The connector of the charger 

is loose or disconnected

Item

Fault Cause

Troubleshooting Methods

Abnormal 

sound when 

riding

1. Adjust the tightness of the secondary 

chain

2. Adjust the tightness of the primary belt

3. dust in brake disc and brake pads, 

need to be cleaned; The brake calipers 

are loose or improperly installed

2.Belt tightness is inappropri-

ate
3. The braking system is not 

properly installed

1.The tightness of the chain is 

inappropriate 

Other Fault

In case of the above situation, please 

contact the local authorized dealer, do 

not dissemble the above parts without 

authorization, otherwise it might void 

your warranty.

2.The motor, controller, char-

ger, and battery are damaged

1. When you encounter a fault 

that cannot be solved or iden-

tified by yourself according to 

the instructions above

 

Содержание Light Bee QL3000DY



















Отзывы: