2. When inspection is needed, it should be carried out in a safe place and pay close attention
to the surrounding environment.
3.If there is any abnormality during the inspection, please rectify the abnormality before
riding. If the problem is difficult for you to solve, please contact Surron or the local authorized
dealer.
CAUTION
1. The front and rear brakes are disc brakes. When the brake pads are worn severely, please
replace them as soon as possible.
2. Keep the disc brake system clean in daily basis use and avoid long-term adhesion of
sediment, especially oil pollution.
Check Operational Unit
1. Check if the suspension is bent, deformed, or damaged.
Check if the front fork is damaged, loose or oil leakage and other faults. Shake the handlebars
up and down to check whether there is any abnormal sound caused by the front fork fault. If
the front fork is malfunctioned, please contact Surron or the local authorized dealer.
2. Check Brakes
Check if the free space of the brake lever is within the specified range (15-30mm). Adjust If it
does not meet the requirements after measurement.
3.Check if the brakes function well. Please ride at low speed on dry flat road for inspection,
and use the front and rear brakes respectively to check their braking effective.
4. Check Tires
The tires will be damaged by glass, stones and other matter on the ground. Please pay
attention to the road condition when riding. Avoid riding in places where tires may be easily
damaged. In addition, you should often check if the tires have distinct cracks and other
damages.
1）Check the tire pressure with the tire pressure gauge when in the cooling condition.
2）Check if there are cracks, damages or abnormal wear.
3）Check if the spokes of the wheel are loose.
4）Check the tightness of the chain. Up and down 10-20mm.
5）Check the depth of tire grooves.
Check tire wear, groove depth. If wear reached 2/3 of the convex block, the tire should be
replaced. When there is abnormal sound or swing in the tire, please contact your local
authorized dealer for inspection and maintenance.
The pivot shaft nut locking torque should be 30 N·m, and the rear axle nut locking torque
should be 40 N·m, The front axle screw locking torque depend on the front fork.
CAUTION
1.The belt tension has been adjusted before delivery. Please do not adjust it without permis-
sion.
2.Hold the brake lever tightly. If the braking performance is still not good, check the
cleanness of the disc.
If the problem cannot be solved, please contact your local authorized dealer for inspection.
Check the Battery
1. Check the Power
The bike is powered by a sealed lithium-ion battery. The battery should be fully charged
before the inspection. Use a multimeter to test the positive and negative voltage of the
discharge port, the normal full voltage should be between 67-67.2V.
2. Check Battery Appearance
Check if the battery’s upper and lower sealing caps and the lcd screen are damaged. It will
cause water get into the power pack if the sealing is damaged. fai Contact the local
authorized dealer if the battery case or cap is damaged.
CAUTION
1. Before installing or removing the battery, please close the key switch and turn off the air
circuit switch, and close the sealant cap of charging port.
2. If the battery cannot be put into the battery compartment, please take out the battery and
check if the battery is stuck by other objects such as cable harness.
3. It is recommended that in winter the indoor temperature for battery storage should be
above 0℃ (32°F) and the battery remaining capacity should be checked regularly.
Charging and Charger Usage
1.When charging, you are required to use the OEM charger. Do not use third-party charger, it
might damage the battery and cause serious injury.
2. Check if the input voltage of the charger is same with the voltage of the power supply.
3.When the battery is fully charged, the charger will automatically stop charging. Avoid
Waterproof Rate
Bike System Type
Tire
IP65
Aluminum Alloy
Front Wheel：70/100-19
Rear Wheel：70/100-19
Charging Time
4h
Riding Mode
Assistance Functions
USB Charger
ECO mode
Regen(on SPORTS mode)
USB 5V2.4A
DC-60V（10A）
Front and Rear Brakes
Secondary Transmission System
Charger Type
Chain 420- 106links
230mm Hydraulic Disc Brake
Other Statements
The range varies greatly depending on the test environment. The range is
measured under conditions of 75kg rider, ambient temperature 28-35℃, and
constant speed 35-40km/h.
1.Chongqing Qiulong Technology Co.,Ltd., continuously improves the product quality and
performance. Therefore, this manual contains the most latest available product information
at the time of printing. Because of this, it is possible that your motorcycle may differ from the
information supplied in this Owner’s Manual. If there is any difference between the logo or
picture in the manual and the actual product, please refer to the actual product.
2.To the extent permitted by law, Chongqing Qiulong Technology Co.,Ltd., reserves rights to
interpret and explain this statement.
3.This Declaration shall be governed by the laws of the People's Republic of China (except the
laws of Hong Kong and Macao Special Administrative Regions and Taiwan Region of China).
Chongqing Qiulong Technology Co.,Ltd., is not liable for all claims, liabilities and losses
caused or likely to be resulted from consumers' violation of the terms above. Riders should be
responsible for unforeseeable or unavoidable risks while riding.
4.If you want to resell or give away your Surron Light Bee off-road motorcycle, please do not
forget to pass along this manual as it is part of the product. If you have any questions, please
contact Chongqing Qiulong Technology Co.,Ltd., Thank you again for your choice and trust in
us.
Circuit Diagram
H
o
rn
S
wi
tc
h
H
o
rn
USB
5V
2.4A
light
gr
een
light
gr
een
gr
een
yellow
g
rr
en
b
lu
e
re
d
w
ri
te
re
d
w
ri
te
re
d
b
la
ck
Br
ak
e S
witch
+12V
Tilt
Switch
(-)
Sid
es
ta
nd
Sw
itc
h (-
)
Co
nv
ert
er
re
d
b
la
ck
Electric
Contr
ol
Lock
re
d
Fu
se 5
A
red
Power Pack
A
ir
S
w
itch
MCU
green
yellow
pink
green
green
green
blue
green
Motor Controller
Mode
Selection
Throttle
contro
BLDC Motor
Dashboard
Assembly
black
black
black
Headlight
Taillight
Hall
blue
H
all
ye
llo
w
H
all
gre
en
Pha
se
wir
e
yellow
Pha
se
wir
e
gr
ee
n
Pha
se
wir
e
blu
e
re
d
D
Z47-125/100A
Charger
Charging Circuit Protection Diagram
Lithium-ion
Battery
220V
10A
+
_
~
23
24
In principle, the first inspection (also known as the first maintenance) can be done at
10-30km if ride normally.
Check Parts
1. The tightness of the spokes on the rear wheel
2. If there is a gap in the headset
3. Check the tightness of chain
4.Belt tightness inspection. (There may be some friction on the new belt, which can be waxed
on both sides of the belt.)
5. Suspension adjustment. Check if there is oil leakage, and if the compression and rebound
damping is in the correct position.(Note: During adjustment, do not turn the adjusting knob
to the extreme position.)
6.Check the tightness of all screws on the handlebars.
WARNING：During the whole maintenance process, the bike
cannot be powered on, which means you cannot do mainte-
nance with the bike is powered on.
Extra attention should be paid to your safety during the inspection.
1. Choose a wide, flat area to park your bike.
connecting the charger to the power supply for a long time.
4. Users are prohibited to disassemble the battery, disassemble battery without permission
may cause serious injury.
5. When the battery is under over-discharge protection, it needs to be re-activated. Please
refer to P25 < Troubleshooting > for activation method.
Motor and Controller Usage and Maintenance
1. Check tightness of the motor screws regularly.
2. Check the motor and controller insulation condition regularly.
3. Check the fuse condition regularly.
4. Do not wade in deep water, it might affect the motor operation.
CAUTION
When the temperature of the motor and the controller is too high or the battery capacity is too
low, the bike will automatically reduce the power to protect the powertrain.
Replace Fuse
If the speedometer, horn, and headlight do not work after the air circuit switch and key switch
are turned ON, the fuse may be melted. If the fuse needs to be replaced, please turn off the
air circuit switch first. The operation method is as follows:
1. Open the battery compartment cap, turn off the air circuit switch, take out the battery, the
fuse box can be seen in front of the air circuit switch, and open the fuse box. (the fuse box is
wrapped with black insulation tape)
2.Replace the broken fuse with the auxiliary one.Close the fuse box,install the battery,and
close the cover of the battery compartment.
Items
QL3000DY
yellow
pink
gr
een
w
rit
e
gr
een
black
gr
een
gr
een
gr
een
gr
een
gr
een
black
black
black
black
black
black
white
green
yellow
blackbr
own
blackwrite
gr
een
write
re
d
write
black
brown
