Supero X7SBU Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 89

background image

3-4

X7SBU User's Manual

e-mail at [email protected], by phone at:(408) 503-8000, option 2, or by
fax at (408)503-8019.

3-3 Frequently Asked Questions

Question: What type of memory does my motherboard support?

Answer:

Both Unbuffered ECC and Non-ECC memory modules are sup-

ported. However, the functionality of ECC is not supported by DDR3 1600 MHz
memory.X7SBU supports DDR3 up to 1600 MHz;. You can only install up to
two 1600 MHz modules on the X7SBU (with one module in DIMM1B slot or
DIMM2B slot or with two modules in both DIMM 1B and DIMM 2B slots

Question: How do I update my BIOS?

Answer:

It is recommended that you

do not

upgrade your BIOS if you are not

experiencing any problems with your system. Updated BIOS files are located

on our web site at

http://www.supermicro.com/support/bios/

. Please check our

BIOS warning message and the information on how to update your BIOS on our

web site. Select your motherboard model and download the BIOS (.rom) file to

your computer. Also, check the current BIOS revision and make sure that it is

newer than your BIOS before downloading. You may choose the zip file or the
.exe file. If you choose the zipped BIOS file, please unzip the BIOS file onto a
bootable device or a USB pen/thumb drive. To flash the BIOS, run the batch
file named “flash.bat” with the new BIOS .rom file from your bootable device or

USB pen/thumb drive. Use the following format:

F:\> flash xxxxxxxx.rom <Enter>

Note:

Be sure to insert a space immediately after “flash” and use only the file

named “flash.bat” to update the BIOS.

When completed, your system will automatically reboot. If you choose the .exe

file, please run the .exe file under Windows to create the BIOS flash floppy disk.
Insert the floppy disk into the system you wish to flash the BIOS. Then, boot
the system to the floppy disk. The BIOS utility will automatically flash the BIOS

without any prompts. Please note that this process may take a few minutes to
complete. Do not be concerned if the screen is paused for a few minutes.

Warning

: Do not shut down or reset the system while updating the BIOS to

prevent possible system boot failure!

When the BIOS flashing screen is completed, the system will reboot and will

show “Press F1 or F2”. At this point, you will need to load the BIOS defaults.

Press <F1> to go to the BIOS setup screen, and press <F9> to load the default
settings. Next, press <F10> to save and exit. The system will then reboot.

«
...
50
51
52
53
54
...
»

Содержание X7SBU


























































































Отзывы:

Нет отзывов

Похожие инструкции для X7SBU

Бренд: ON Semiconductor Страницы: 17

Бренд: Sleipner Страницы: 28

Бренд: Gigabyte Страницы: 36

Бренд: ASROCK Страницы: 26

Бренд: Gigabyte Страницы: 74

Gamefisher 298.586180

Бренд: Gamefisher Страницы: 23

Бренд: Gigabyte Страницы: 143

Бренд: NXP Semiconductors Страницы: 19

Бренд: Quantum Design Страницы: 59

Бренд: Quantum Design Страницы: 75

Бренд: Fujitsu Страницы: 12

ADA-91270-90340-100PFV

Бренд: Fujitsu Страницы: 24

Бренд: Fujitsu Страницы: 64

8FX MB2146-510-01-E

Бренд: Fujitsu Страницы: 25

Бренд: Biostar Страницы: 55

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды