Supero X7SBU Скачать руководство пользователя страница 38

Страница: 38 / 89

X7SBU User's Manual

2-20

Fan Headers

The X7SBU has six fan headers (Fan1 to

Fan6) including five chassis/system fan head

ers (Fan1 to Fan5) and one CPU Fan (CPU
Fan6). All these fan headers support 4-pin
fans. However, Pins 1-3 of the fan headers are
backward compatible with the traditional 3-pin

fans. See the table on the right for pin defini

tions. The onboard fan speeds are controlled
by Thermal Management via BIOS Hardware
Monitoring in the Advanced Setting.

Notes:

1. The Default setting is Disabled.

2. Please use all 3-pin fans or all 4-pin
fans on the motherboard. Please do not

4-pin Fan Header

Pin Definitions (Fan1-6)

Pin# Definition

Ground

+12V

Tachometer

PWR Modulation

Fan 1 (CPU Fan)

Fan 2

Fan 3

Fan 4

Fan 5

Fan 6

G. VGA

VGA Connector

A VGA connector (J16) is located between
COM1 and JLAN1 on the IO backplane. Refer
to the board layout below for the location.

Содержание X7SBU


























































































Результаты поиска

Содержание X7SBU

Отзывы:

Похожие инструкции для X7SBU

Бренды по названию

Популярные бренды

Supero X7SBU, Руководство пользователя

Результаты поиска

Содержание X7SBU

Отзывы:

Похожие инструкции для X7SBU

Бренды по названию

Популярные бренды