Supero H8DA6+ Скачать руководство пользователя страница 30

Страница: 30 / 76

H8DA6+/I+(-F) Serverboard User's Manual

2-10

Universal Serial Bus Ports

Six Universal Serial Bus ports (USB 2.0) are

located beside the LAN ports. Two additional

Type A ports (USB4/5) are included on the

motherboard near the PCI Slot 1. See the

table on the right for pin defi nitions.

Universal Serial Bus Ports

Pin Defi nitions (USB0/1, USB4/5)

USB0
Pin # Defi nition

USB1
Pin # Defi nition

+5V

PO-

PO+

Ground

USB Headers

Two USB 2.0 headers (USB2/3) are also

included on the motherboard. These may

be connected to provide front side access. A

USB cable (not included) is needed for the

connection. See the table on the right for

pin defi nitions.

Universal Serial Bus Headers

Pin Defi nitions (USB2/3)

USB2
Pin # Defi nition

USB3
Pin # Defi nition

+5V

PO-

PO+

Ground

Key

Fan Header

Pin Defi nitions

Pin# Defi nition

Ground

+12V

Tachometer

PWR Modulation

Fan Headers

This motherboard has eight fan headers

(Fan1 to Fan8). These 4-pin fans headers

are backward compatible with 3-pin fans.

However, fan speed control is available

for 4-pin fans only. The fan speeds are

controlled by the BIOS. See the table on the

right for pin defi nitions

Note:

NC indicates no connection.

Serial Ports

The COM1 serial port is located

beside the VGA port. Refer to the

motherboard layout for the location of

the COM2 header. See the table on

the right for pin defi nitions.

Note:

NC indicates no connection.

Serial Port Pin Defi nitions

(COM1/COM2)

Pin # Defi nition

DCD

DSR

RXD

RTS

TXD

CTS

DTR

Ground

Содержание H8DA6+













































































Результаты поиска

Содержание H8DA6+

Отзывы:

Похожие инструкции для H8DA6+

Бренды по названию

Популярные бренды

Supero H8DA6+, Руководство пользователя

Результаты поиска

Содержание H8DA6+

Отзывы:

Похожие инструкции для H8DA6+

Бренды по названию

Популярные бренды