Supermicro SuperWorkstation 5039A-IL Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 112

Supermicro SuperWorkstation 5039A-IL Скачать руководство пользователя страница 38

38

Chapter 4: Motherboard Connections

Standby Power

Pin Definitions

Pin#

Definition

1

+5V Standby

2

Ground

3

N/A

Trusted Platform Module Header

Pin Definitions

Pin#

Definition

Pin#

Definition

1

LCLK

2

Ground

3

LFRAME#

4

<(KEY)>

5

LRESET#

6

+5V

7

LAD3

8

LAD2

9

+3.3V

10

LAD1

11

LAD0

12

Ground

13

SMB_CLK

14

SMB_DAT

15

+3V Stdby

16

SERIRQ

17

Ground

18

CLKRUN#

19

LPCPD#

20

LDRQ#

TPM/Port 80 Header

A Trusted Platform Module (TPM)/Port 80 header is located at JTPM1 to provide TPM support
and Port 80 connection. Use this header to enhance system performance and data security.

Onboard Power LED (JLED1)

An onboard Power LED header is located at JLED1. This Power LED header is connected
to Front Control Panel located at JF1 to indicate the status of system power.

Onboard Power LED Connection

Pin Definitions

Pin#

Definition

1

VCC

2

No Connection

3

Connection to Power LED on JF1

Standby Power Header

The Standby Power header is located at JSTBY1. You must have a card with a Standby
Power connector and a cable to use this feature.

«
...
36
37
38
39
40
...
»

Содержание SuperWorkstation 5039A-IL

















































































































Отзывы:

Нет отзывов