Supermicro SUPERSERVER 6018TR-T Скачать руководство пользователя страница 68

Страница: 68 / 144

5-16

SUPERSERVER 6018TR-T/TF User's Manual

5-8 Connector

Defi nitions

Power Connectors

Two 20-pin power supply connectors and

a 4-pin power connector are located on

the motherboard. The two 20-pin power

connectors (J4/J6) are used as main

power supply to the system, while the

4-pin power connector (JP3) provides

power to the HDD panel for Chassis

808/809. These power connectors meet

the SSI EPS 12V specifi cation and must

be connected to your power supply to

provide adequate power to the system.

See the tables below for pin defi nitions.

Warning!

To avoid damaging the power

supply or the motherboard, please connect

the power supply to a 20-pin power

connector located at J4 or J6, and connect

the 4-pin power connector (JP3) to the

backplane or the HDD to provide adequate

power to your system. Failure to do so may

void the manufacturer warranty on your

power supply and motherboard.

20-pin Main Connector

Pin Defi nitions (J4/J6)

Pin# Defi nition

PS_ON#

Ground

P5V_STBY

Ground

No Connections

P12V

4-pin HDD-Panel PWR

Pin Defi nitions (JP3)

Pin# Defi nition

P12V

Ground

P5V

Содержание SUPERSERVER 6018TR-T

















































































































































Результаты поиска

Содержание SUPERSERVER 6018TR-T

Отзывы:

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 6018TR-T, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 6018TR-T

Отзывы:

Бренды по названию

Популярные бренды