Supermicro SUPERSERVER 6018TR-T Скачать руководство пользователя страница 14

Страница: 14 / 144

1-4

SUPERSERVER 6018TR-T/TF User's Manual

SATA Subsystem

The SC808 supports up to four (4) 3.5" hot-swap SATA drives in trays (two for each

node). These drives are hot-swappable units and are connected to a backplane that

provides power and control.

Note:

The operating system you use must have RAID support to enable the hot-

swap capability of the drives.

Front Control Panel

SC808BTS-1K03BP chassis includes two front panels on the handles of the chassis

which control each of the systems. Each control panel on the SUPERSERVER

6018TR-T/TF provides you with system monitoring and control for one server

node. LEDs indicate system power, HDD activity, network activity, system overheat

and power supply failure. A main power button and a system reset button are also

included.

I/O Ports

The SC808 is an proprietary form factor chassis designed to be used in a 1U

rackmount confi guration. The SC808 chassis provides a low-profi le add-on card

slot, a COM port, a VGA port, two USB 2.0 ports , one IPMI Ethernet port and two

gigabit Ethernet ports per node.

Cooling System

The SC808 chassis accepts six (6) 4-cm system fans powered from either backpane

or the serverboards. If not powered from the backpane, the SC808BTS-1K03BP

model chassis powers three fans from each of the two motherboards, so that when

one of the motherboard drawers is removed, the other motherboards will continue

running its fans.

Note:

The fans in this system are NOT redundant, hot-plug.

Air Shrouds

The SC808 chassis includes two plastic air shrouds that direct the airfl ow where

cooling is needed on each serverboard. Always use the air shroud included with

your chassis on each serverboard.

Содержание SUPERSERVER 6018TR-T

















































































































































Результаты поиска

Содержание SUPERSERVER 6018TR-T

Отзывы:

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 6018TR-T, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 6018TR-T

Отзывы:

Бренды по названию

Популярные бренды