Supermicro SUPERSERVER 6013L-8 Скачать руководство пользователя страница 55

Страница: 55 / 108

Chapter 5: Advanced Motherboard Setup

5-21

Chassis/Overheat Fan
Select

JP48 allows you to select to use

either the chassis fan or the over-

heat fan. The default position is

closed to select the chassis fan.

S e e t h e t a b l e o n t h e r i g h t f o r

jumper settings.

Jumper

Position

Open

Closed

Definition

Overheat Fan

Chassis Fan

Chassis/Overheat Fan

Select Jumper Settings

(J48)

GLAN1 Enable/Disable

Change the setting of jumper JP54

to enable or disable the onboard

LAN1 or NIC (Network Interface

Card) on the motherboard. See

the table on the right for jumper

settings. The default setting is

Enabled.

GLAN2 Enable/Disable

Change the setting of jumper JP4

to enable or disable the onboard

LAN2 or NIC (Network Interface

Card) on the motherboard. See

the table on the right for jumper

settings. The default setting is

Enabled.

Jumper

Position

Pins 1-2
Pins 2-3

Definition

Enabled

Disabled

LAN1 (NIC)

Enable/Disable

Jumper Settings

(JP54)

Jumper

Position

Pins 1-2
Pins 2-3

Definition

Enabled

Disabled

LAN2 (NIC)

Enable/Disable

Jumper Settings

(JP4)

Watch Dog

JP3 controls the Watch Dog function.

Watch Dog is a system monitor that

takes action when a software appli-

cation freezes the system. Pins 1-2

will have WD reset the system if a

program freezes. Pins 2-3 will gener-

ate a non-maskable interrupt for the

p r o g r a m t h a t h a s f r o z e n ( r e q u i r e s

software implementation). See the

table on the right for jumper settings.

Watch Dog must also be enabled in

BIOS.

Jumper

Position

Pins 1-2
Pins 2-3

Open

Definition

W D to Reset

W D to NMI

Disabled

W atch Dog

Jumper Settings (JP3)

Содержание SUPERSERVER 6013L-8













































































































Результаты поиска

Содержание SUPERSERVER 6013L-8

Отзывы:

Похожие инструкции для SUPERSERVER 6013L-8

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 6013L-8, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 6013L-8

Отзывы:

Похожие инструкции для SUPERSERVER 6013L-8

Бренды по названию

Популярные бренды