Supermicro SUPERSERVER 6013L-8 Скачать руководство пользователя страница 39

Страница: 39 / 108

Chapter 5: Advanced Motherboard Setup

5-5

5-3

Connecting Cables

Now that the processors and heatsinks are installed, the next step is to

connect the cables to the board. These include the data (ribbon) cables for

the peripherals and control panel and the power cables.

Connecting Data Cables

The ribbon cables used to transfer data from the peripheral devices have

been carefully routed in preconfigured systems to prevent them from block-

ing the flow of cooling air that moves through the system from front to back.

If you need to disconnect any of these cables, you should take care to keep

them routed as they were originally after reconnecting them (make sure the

red wires connect to the pin 1 locations). If you are configuring the sys-

tem, keep the airflow in mind when routing the cables. The following data

cables (with their motherboard connector locations noted) should be con-

nected. See the motherboard layout figure in this chapter for connector

locations.

IDE Device Cables (J18 and J19)

Floppy Drive Cable (JP12)

Ultra 320 LVD SCSI Cables (JA1, JA2)

Control Panel Cable (JF1, see next page)

Connecting Power Cables

The X5DLR-8G2+ has a 24-pin primary power supply connector desig-

nated "ATX Power" for connection to the ATX power supply. Connect

the appropriate connector from the power supply to the "ATX Power"

connector to supply power to the motherboard. A 12V, 8-pin secondary

power connector designated PWR_SEC must also be connected to your

power supply. See the Connector Definitions section in this chapter for

power connector pin definitions.

Содержание SUPERSERVER 6013L-8













































































































Результаты поиска

Содержание SUPERSERVER 6013L-8

Отзывы:

Похожие инструкции для SUPERSERVER 6013L-8

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 6013L-8, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 6013L-8

Отзывы:

Похожие инструкции для SUPERSERVER 6013L-8

Бренды по названию

Популярные бренды