Supermicro SUPERSERVER 1028UX-LL1-B8, Руководство пользователя

Страница: 36 / 74

Chapter 5: Advanced Serverboard Setup
5-13 5-12
SUPERSERVER 1028UX-LL1-B8/LL2-B8/LL3-B8 User's Manual
Reset Button
The Reset Button connection is lo-
cated on pins 3 and 4 of JF1. Attach
it to the hardware reset switch on the
computer case. Refer to the table on
the right for pin definitions.
Power Button
The Power Button connection is
located on pins 1 and 2 of JF1. Mo-
mentarily contacting both pins will
power on/off the system. This button
can also be configured to function
as a suspend button (see the Power
Button Mode setting in BIOS). To turn
off the power when set to suspend
mode, depress the button for at least
4 seconds. Refer to the table on the
right for pin definitions.
Reset Button
Pin Definitions (JF1)
Pin# Definition
3 Reset
4 Ground
Power Button
Pin Definitions (JF1)
Pin# Definition
1 Signal
2 Ground
Chassis Intrusion
A Chassis Intrusion header is located
at JL1. Attach an appropriate cable
from the chassis to inform you of a
chassis intrusion when the chassis
is opened.
Chassis Intrusion
Pin Definitions
Pin# Definition
1 Intrusion Input
2 Ground
Fan Header
Pin Definitions
Pin# Definition
1 Ground
2 +12V
3 Tachometer
4 Pulse Width Modulation
(PWM)
Fan Headers
The serverboard has eight system/
CPU fan headers (Fan 1~Fan 8).
All are 4-pin fans headers, which
are backward compatible with tradi -
tional 3-pin fans. Fan speed control
is available for 4-pin fans only. The
fan speeds are controlled by thermal
management via IPMI. See the table
on the right for pin definitions.
Internal Speaker
The Internal Speaker, located at SP1,
can be used to provide audible indica-
tions for various beep codes. See the
table on the right for pin definitions.
Internal Speaker
Pin Definition
Pin# Definitions
Pin 1 Pos. (+) Beep In
Pin 2 Neg. (-) Alarm
Speaker
TPM Header/Port 80
A Trusted Platform Module/Port 80
header is located at JTPM1 to provide
TPM support and Port 80 connection.
Use this header to enhance system
performance and data security. See
the table on the right for pin defini -
tions.
TPM/Port 80 Header
Pin Definitions
Pin # Definition Pin # Definition
1 LCLK 2 GND
3 LFRAME# 4 <(KEY)>
5 LRESET# 6 +5V (X)
7 LAD 3 8 LAD 2
9 +3.3V 10 LAD1
11 LAD0 12 GND
13 SMB_CLK4 14 SMB_DAT4
15 +3V_DUAL 16 SERIRQ
17 GND 18 CLKRUN# (X)
19 LPCPD# 20 LDRQ# (X)
DOM Power Connectors
Two power connectors for SATA DOM
(Disk On Module) devices are located
at JSD1 and JSD2. Connect an ap-
propriate cable here to provide power
for your SATA DOM devices.
DOM PWR
Pin Definitions
Pin# Definition
1 +5V
2 Ground
3 Ground
I-SGPIO2 Header
A Serial-Link General Purpose Input/
Output header (I-SGPIO2) supports
the S-SATA 0-3 ports. See the table
on the right for pin definitions.
I-SGPIO
Pin Definitions
Pin# Definition Pin Definition
1 NC 2 NC
3 Ground 4 Data
5 Load 6 Ground
7 Clock 8 NC
NC = No Connection