Supermicro Supero H8SGL Скачать руководство пользователя страница 33

Страница: 33 / 82

Chapter 2: Installation

2-7

2-5 PCI Expansion Cards

A riser card is used to support one standard size (full height full length) PCI

expansion card.

Installing a PCI Expansion Card

1. Confi rm that you have the correct riser card for your chassis model and the

add-on card includes a standard bracket.

2. Remove the chassis cover.

3. Install the riser card by sliding card into the appropriate slot in the

serverboard.

4. Choose the PCI slot shield in which to place the add-on card.

5. In that slot, open the PCI slot shield lever and slide the shield sideways.

6. From inside the chassis, remove the PCI slot shield.

7. Slide the add-on card into the riser card and attach the add-on card bracket

in place of the PCI slot shield.

8. Secure the add-on card by closing the PCI slot shield lever.

9. Connect cables to the add-on card as necessary.

Possible System Memory Allocation & Availability

System Device

Size

Physical Memory Available
(4 GB Total System Memory)

Firmware Hub fl ash memory (System BIOS)

1 MB

3.99 GB

Local APIC

4 KB

3.99 GB

Area Reserved for the chipset

2 MB

3.99 GB

I/O APIC (4 Kbytes)

4 KB

3.99 GB

PCI Enumeration Area 1

256 MB

3.76 GB

PCI Express (256 MB)

256 MB

3.51 GB

PCI Enumeration Area 2 (if needed) - aligned on
256 MB boundary

512 MB

3.01 GB

VGA Memory

16 MB

2.85 GB

TSEG

1 MB

2.84 GB

Memory available for the OS & other applications

2.84 GB

Содержание Supero H8SGL



















































































Результаты поиска

Содержание Supero H8SGL

Отзывы:

Похожие инструкции для Supero H8SGL

Бренды по названию

Популярные бренды

Supermicro Supero H8SGL, Руководство пользователя

Результаты поиска

Содержание Supero H8SGL

Отзывы:

Похожие инструкции для Supero H8SGL

Бренды по названию

Популярные бренды