Supermicro Supero H8SGL Скачать руководство пользователя страница 28

Страница: 28 / 82

H8SGL(-F) SERVERBOARD USER'S MANUAL

2-2

2-2 Processor and Heatsink Installation

Warning:

Exercise extreme caution when handling and installing the processor. Always

connect the power cord last and always remove it before adding, removing or changing

any hardware components.

Installation Procedure

Follow the procedures as listed below to install the motherboard into a chassis.

1. Install the processor(s) and the heatsink(s).

2. Install the motherboard in the chassis.

3. Install the memory and add-on cards.

4. Finally, connect the cables and install the drivers.

Installing the Processors

1. Begin by removing the cover plate that

protects the CPU. Lift the lever on the

CPU socket until it points straight up.

2. With the lever raised, lift open the silver

CPU retention plate.

Содержание Supero H8SGL



















































































Результаты поиска

Содержание Supero H8SGL

Отзывы:

Похожие инструкции для Supero H8SGL

Бренды по названию

Популярные бренды

Supermicro Supero H8SGL, Руководство пользователя

Результаты поиска

Содержание Supero H8SGL

Отзывы:

Похожие инструкции для Supero H8SGL

Бренды по названию

Популярные бренды