Supermicro Supero H8SGL Скачать руководство пользователя страница 19

Страница: 19 / 82

Chapter 1: Introduction

1-7

1-3 Motherboard

Features

CPU

•

Single AMD Opteron 6000 series processor

Note: Refer to our web site for details on supported processors.

Memory

•

Single/Dual/Tri/Quad channel DIMM slots supporting up to 256 GB of registered

ECC or 64 GB of unbuffered ECC/non-ECC DDR3-1600/1333/1066 Mhz speed,

1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size SDRAM

Note: Refer to Section 2-4 before installing memory and our web site for recommended DIMMs.

Chipset

•

AMD SR5650 chipset and one SP5100 Southbridge chipset

Expansion Slots

•

One (1) PCI-Express x8 (in x16 slot) Gen. 2

•

One (1) PCI-Express x8 Gen. 2

•

One (1) PCI-Express x4 (in x8 slot) Gen. 2

•

Three (3) PCI slots

BIOS

•

16 Mb AMI BIOS® SPI Flash ROM

•

APM 1.2, DMI 2.3, PCI 2.2, ACPI 1.0 (ACPI 2.0 is BIOS supported), SMBIOS

2.3, Real Time Clock Wakeup, Plug and Play (PnP), BIOS resume hot keys,

Hardware BIOS Virus Protection

PC Health Monitoring

•

Onboard voltage monitors

•

Fan status monitor with fi rmware/software on/off and speed control

•

Watch Dog

•

Environmental temperature monitoring via BIOS

•

Power-up mode control for recovery from AC power loss

•

System resource alert (via included utility program)

•

Auto-switching voltage regulator for the CPU core

•

CPU thermal trip support

•

C temperature sensing logic

•

Chipkill Support

Содержание Supero H8SGL



















































































Результаты поиска

Содержание Supero H8SGL

Отзывы:

Похожие инструкции для Supero H8SGL

Бренды по названию

Популярные бренды

Supermicro Supero H8SGL, Руководство пользователя

Результаты поиска

Содержание Supero H8SGL

Отзывы:

Похожие инструкции для Supero H8SGL

Бренды по названию

Популярные бренды