Supermicro MBD-X8STI-F Скачать руководство пользователя страница 52

Страница: 52 / 111

Chapter 2: Installation

2-27

LSI 1068E

NIC4 LED

JBMC1

Wake-On-LAN

The Wake-On-LAN header is located at

JWOL on the motherboard. See the table on

the right for pin deinitions. (You must also

have a LAN card with a Wake-On-LAN con-

nector and cable to use this feature.)

Wake-On-LAN

Pin Deinitions

(JWOL)

Pin# Deinition

+5V Standby

Ground

Wake-up

A. WOL

B. I-Button (X8STi-3F only)

I-Button (X8STi-3F only)

An onboard I-Button, located next to the loppy

drive, is an 1-wire computer chip enclosed in

a durable stainless steel can. I-Button stores

instructions, provides electronic interface and

allows HostRAID to operate with Mega-RAID

irmware. Please note that I-Button does not

come with your motherboard.

Note:

RAID 5 is supported when the

I-Button (AOC-IButton68) is installed

on the motherboard. For more infor-

mation on the AOC-IButton68, please

refer to http://www.supermicro.com/

products/accessories/addon/AOC-

IButton68.cfm.

Содержание MBD-X8STI-F
















































































































Результаты поиска

Содержание MBD-X8STI-F

Отзывы:

Похожие инструкции для MBD-X8STI-F

Бренды по названию

Популярные бренды

Supermicro MBD-X8STI-F, Руководство пользователя

Результаты поиска

Содержание MBD-X8STI-F

Отзывы:

Похожие инструкции для MBD-X8STI-F

Бренды по названию

Популярные бренды