Supermicro MBD-X8STI-F Скачать руководство пользователя страница 103

Страница: 103 / 111

B-2

X8STi/X8STi-F/X8STi-3F/X8STi-LN4 User's Manual Guide

B-2 Installing the Windows OS to a Non-RAID System

1. Insert Microsoft's Windows XP/2003 Setup CD in the CD Driver, and the

system will start booting up from CD.

Press the <F6> key when the message-" Press F6 if you need to install a

third party SCSI or RAID driver" displays.

3. When the Windows XP/2003 Setup screen appears, press "S" to specify ad-

ditional device(s).

Insert the driver diskette you want to install into Drive A: and press the <En

ter> key.

Press the <Enter> key to proceed with the installation process. (If you need

to specify any additional devices to be installed, do it at this time.) Once all

devices are speciied, press the <Enter> key to continue with the installation.

From the Windows XP/2003 Setup screen, press the <Enter> key. The
XP/2003 Setup will automatically load all device iles and then continue with

the Windows XP/2003 installation.

7. After the Windows XP/2003 OS Installation is completed, the system will auto-

matically reboot.

8. Insert the Supermicro Setup CD that came with your motherboard into the CD

Drive during system boot, and the main screen shown on Page C-1 in Ap-

pendix C will display. Follow the instructions given in Appendix C to complete

software installation.

Содержание MBD-X8STI-F
















































































































Результаты поиска

Содержание MBD-X8STI-F

Отзывы:

Бренды по названию

Популярные бренды

Supermicro MBD-X8STI-F, Руководство пользователя

Результаты поиска

Содержание MBD-X8STI-F

Отзывы:

Бренды по названию

Популярные бренды