Supermicro MBD-X8STI-F Скачать руководство пользователя страница 108

Страница: 108 / 111

Appendix D: BIOS Recovery

D-1

Appendix D - BIOS Recovery

The recovery procedure described in this section is to be used only when advised

by your Supermicro Technical Support representative, or in cases of emergencies

where the system no longer can boot due to a corrupted BIOS. DO NOT re-program

(re-lash) the BIOS if your system is running properly.

D-1 Recovery Process from a USB Device/Drive
(Recommended Method)

If the BIOS ile is corrupted and the system is not able to boot up, this feature will

allow you to recover the BIOS image using a USB-attached device. A USB Flash

Drive or a USB CD/DVD ROM/RW drive may be used for this purpose. Please

note that a USB Hard Disk drive is NOT supported at this time. Below is a two-part

procedure to recover the BIOS:

Part 1: Boot Sector Recovery Process

Using a different system, download and copy the correct BIOS binary image

into a USB lash device or a writable CD/DVD disc's Root "\" Directory. Rename the
downloaded ile to "super.rom", so the recovery process can recognize and read
the BIOS binary ile.

Insert the USB device that contains the new BIOS binary image (“super.rom”)

and power the system down.

While powering on the system, press and hold <Ctrl> and <Home> simultane

ously on your keyboard until the USB device's LED indicator comes on. This will

take a few seconds or up to one minute.

Once the USB device's LED is on, release the <Ctrl> and <Home> keys. The

system may generate beep codes to indicate that the BIOS ROM irmware is being

reprogrammed. The screen will also display a message as shown below. DO NOT

INTERRUPT THIS PROCESS!

Содержание MBD-X8STI-F
















































































































Результаты поиска

Содержание MBD-X8STI-F

Отзывы:

Бренды по названию

Популярные бренды

Supermicro MBD-X8STI-F, Руководство пользователя

Результаты поиска

Содержание MBD-X8STI-F

Отзывы:

Бренды по названию

Популярные бренды