Supermicro MBD-X8STI-F Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 111

background image

3-4

X8STi/X8STi-F/X8STi-3F/X8STi-LN4

User's Manual

Question: How do I update my BIOS?

Answer:

It is recommended that you

do not

upgrade your BIOS if you are not

experiencing any problems with your system. Updated BIOS iles are located

on our web site at

http://www.supermicro.com/support/bios/

. Please check our

BIOS warning message and the information on how to update your BIOS on our

web site. Select your motherboard model and download the BIOS (.rom) ile to

your computer. Also, check the current BIOS revision and make sure that it is

newer than your BIOS before downloading. You may choose the zip ile or the
.exe ile. If you choose the zipped BIOS ile, please unzip the BIOS ile onto a
bootable device or a USB pen/thumb drive. To lash the BIOS, run the batch
ile named "ami.bat" with the new BIOS ROM ile from your bootable device or

USB pen/thumb drive. Use the following format:

F:\> ami.bat BIOS-ROM-ilename.xxx <Enter>

Notes:

Always use the ile named “ami.bat” to update the BIOS and insert

a space between "ami.bat" and the ilename. The BIOS-ROM-ilename will

bear the motherboard name (i.e., X8STi) and build version as the extension.

For example, "X8STi.115".

When completed, your system will automatically reboot. If you choose the .exe

ile, please run the .exe ile under Windows to create the BIOS lash loppy disk.
Insert the loppy disk into the system you wish to lash the BIOS. Then, boot
the system to the loppy disk. The BIOS utility will automatically lash the BIOS

without any prompts. Please note that this process may take a few minutes to

complete. Do not be concerned if the screen is paused for a few minutes.

Warning

: Do not shut down or reset the system while updating the BIOS to

prevent possible system boot failure!

When the BIOS lashing screen is completed, the system will reboot and will

show “Press F1 or F2”. At this point, you will need to load the BIOS defaults.

Press <F1> to go to the BIOS setup screen, and press <F9> to load the default
settings. Next, press <F10> to save and exit. The system will then reboot.

Note:

The SPI BIOS chip installed on this motherboard is not removable. To

repair or replace a damaged BIOS chip, please send your motherboard to RMA

at Supermicro for service.

Question:

I think my BIOS is corrupted. How can I recover my BIOS?

Answer:

Please see Appendix D, BIOS Recovery for detailed instructions.

Question:

What's on the CD that came with my motherboard?

Answer:

The supplied compact disc has quite a few drivers and programs

that will greatly enhance your system. We recommend that you review the CD

«
...
67
68
69
70
71
...
»

Содержание MBD-X8STI-F
















































































































Отзывы:

Нет отзывов

Похожие инструкции для MBD-X8STI-F

Бренд: Yamaha Страницы: 20

MachXO5-NX Development Kit

Бренд: Lattice Semiconductor Страницы: 64

Бренд: ON Semiconductor Страницы: 17

Бренд: JETWAY Страницы: 56

Бренд: Beck Страницы: 24

Бренд: BESTEK Страницы: 52

PP-I7RS400 PURE PERFORMANCE II

Бренд: Sapphire Audio Страницы: 44

Бренд: DFI Страницы: 5

Бренд: Gigabyte Страницы: 100

CONROE1333-ESATA2

Бренд: ASROCK Страницы: 226

MT9M031I12STCH-GEVB

Бренд: ON Semiconductor Страницы: 5

Бренд: Intel Страницы: 62

AIMB-742 Socket 478

Бренд: Intel Страницы: 4

Бренд: Gigabyte Страницы: 72

nForce 680i LT SLI

Бренд: XFX Страницы: 137

SUPER i2DMR-8G2

Бренд: Supero Страницы: 78

Бренд: ASROCK Страницы: 125

PHANTOM GAMING B650E PG-ITX WiFi

Бренд: ASROCK Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды