background image

REFRACTORY REPLACEMENT

The intense heat of the fire will normally cause 

hairline cracks in the refractory.  These cracks 

can be minimized by proper curing as described 

in “First Fires”.  They will not normally dimin-

ish the effectiveness of the refractory.  If large 

cracks develop, then the refractory should be 

replaced.  To replace the refractory bricks, fol-

low these steps:

1.  Remove the front refractories

2.  Remove the bottom refractory

3.  Remove the left side refractory

4.  Remove the right side refractory

5.  Remove the back refractory

6.  Remove the front ceramic baffle

7.  Remove the rear ceramic baffle 
To install the new refractories, follow the above 

steps in reverse.

Figure 6

Figure 5 - Door Installation

DOOR INSTALLATION

The door must be installed only when the installation of the fireplace is completed.  All you have 

to do is fit the male part of the hinge, already on the door, to the female part, which is on the 

fireplace. To remove the door, simply pull the door up from the hinges (see Figure 5).  The door 

adjustment has been set at the factory.  If the fit is still not perfect, you can adjust the door using 

the hinge screws.

DOOR ADJUSTMENT

The door may need to be adjusted to be completely airtight. The gaskets’ air-tightness can be 

adjusted using the adjustment screw located on the right side of the fireplace facade (An Allen key 

#1/8 – not supplied - will be necessary for this adjustment).
Checking Door Seal 

A one-inch strip of paper may be used to perform a test of the integrity of the door seal. Close 

the door on the paper in at least eight points.  It is normal to feel only a slight amount of friction. 

The door gasket does not need to be “tight” in all areas, since a small amount of leakage is not 

hazardous or detrimental to the performance of your fireplace.

Figure 7

  WARNING

 

Use only a IHP glass doors, specifically designed for the fireplace.

  The fireplace cannot be operated without door.  Consult your dealer to 

select the correct replacement door.

 

Important! To assure proper alignment of glass doors:  Install this 

fireplace in a square and plumb condition, using shims as necessary 

at sides and/or bottom.

1

2

3

7

6

5

4

Hinges Adjustment

Gasket Adjustment Screw

      WARNING

Disposal of Ashes:  Ashes should 

be placed in a steel container 

with a tight fitting lid and moved 

outdoors immediately.  The 

closed container of ashes should 

be placed on a non-combustible 

floor or on the ground well away 

from all combustible materials, 

pending final disposal.  If the 

ashes are disposed of by burial 

in soil or otherwise locally dis-

persed, they should be retained 

in the closed container until all 

cinders have thoroughly cooled.

1. Front Refractories

2. Bottom Refractory

3. Left Side Refractory

4. Right Side Refractory

5. Back Refractory

6. Front Ceramic Baffle

7. Rear Ceramic Baffle

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

7

Содержание WCT6820WS





























Отзывы: