44
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Care and Operation
900358-00, 01/2018
Innovative Hearth Products
DRT63STTYN Power-Vent Direct-Vent Fireplaces
WARNING
Any safety screen or guard
removed for servicing the appli-
ance must be replaced prior to
operating the appliance.
AVERTISSEMENT
Tout écran ou protecteur retiré
pour permettre l’entretien de
l’appareil doit être remis en
place avant de mettre l’appareil
en marche.
REMOVAL AND INSTALLATION
OF GLASS DOORS, MESH PULL
SCREENS, AND MODESTY PANEL
WARNING
Do not operate appliance with
the glass front removed, cracked
or broken.
AVERTISSEMENT
Ne pas utiliser l'appareil si le
panneau frontal en verre n'est
pas en place, est craqué ou brisé.
Figure 63
Top Flange on
Glass Door Assembly Glass Door Latch (2)
Screws
Glass Door Assembly
CAUTION
RISK OF PERSONAL INJURY
OR PROPERTY DAMAGE.
•
Do NOT abuse glass doors by striking or
slamming shut
•
Never operate fireplace with glass door
assemblies removed.
These direct-vent appliances are designed
to operate only when both glass door
assemblies are installed. Generally, the
glass door assemblies should not be
removed, except when access to compo-
nents within the firebox is required.
•
Securely tighten door latch screws when
reinstalling glass door assemblies to
prevent doors from falling out.
•
Handle glass door assemblies with
extreme care. Replace damaged glass
door assemblies with approved replace-
ment assemblies only.
The door assemblies on this fireplace
contain ceramic glass. Handle with care
to prevent damage. If the door frame
or glass on either assembly becomes
damaged, replace the entire glass door
assembly with a manufacturer-approved
replacement assembly only. Do not
attempt to substitute any materials used
on door assemblies or replace cracked
or broken glass with any other materials.
Installing Glass Doors, Barrier, and
Modesty Panel
(see Figure 63)
NOTE: These instructions do NOT apply to
the Outer Glass Door provided in the Out-
door Kit (for indoor/outdoor installations).
• Only doors certified with the appliance shall
be used.
• Seules des portes certifiées pour cet
appareil doivent être utilisées.
1) Install one of the glass doors, as follows:
a) Retrieve the glass door. Visually inspect
the gasket on the back of the frame.
Gasket surface must be clean, free of
irregularities, and seated firmly.
b) Position the door in front of the firebox
opening, with the top of the door held
away from the fireplace (see
Figure 63
).
c) Lower the bottom of the door assembly
onto the bottom door track, engaging and
centering it in the base channel, and then
gently swing the door up.
d) Using a #3 Phillips screwdriver, fasten the
door frame to the door latches with the
two (2) latch screws. The latches should
pull forward to engage the door frame.
NOTE: Securely tighten latch screws when
reinstalling glass door assembly.
2) Install the modesty panel on the top flange
of the glass door, as follows:
a) Grasp the modesty panel with both hands
(with the open hem facing down).
b) Engage it with the top flange of the glass
door frame by pushing it all the way
down. Make sure the installed modesty
panel is firmly in place.
3) Install the barrier, as follows:
a) Slide the barrier, flat side toward the
fireplace, into the right barrier bracket
with gap below.
b) Reinsert the lower filler piece by sliding
the tab behind the barrier.
c) Center the barrier between the left and
right barrier brackets and lower the bar-
rier until the lower filler piece and barrier
are flush with the bottom of the glass
door.
Removing Glass Doors, Barrier, and
Modesty Panel
(see Figure 9)
1) Remove the barrier, as follows:
a) Lift barrier up by the frame at the top.
b) Remove lower filler piece by pulling down
off of the barrier.
c) Lower barrier and push barrier to left to
release right side. Remove barrier and
set aside for reinstallation
2) Remove the modesty panel from the top
flange of the glass door by firmly pulling up
on it with both hands until it is disengaged.
3) Remove one of the glass doors, as follows:
a) See
Figure 9
.
While holding the top of
the glass door frame in place
, use a #3
Phillips screwdriver to remove the two
(2) screws securing the door frame to
the two (2) door latches.
b) Carefully tilt the top of the glass door
frame away from the unit (as shown in
Figure 9
), and then lift the door assem-
bly up and out of the lower track.
c) Carefully place the glass door assembly
on a padded surface in a safe location to
prevent damage.
WARNING
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
•
Install only when fireplace is OFF and
COLD.
• Fireplace surfaces get EXTREMELY HOT!
• The glass on the front of the fireplace
reaches EXTREMELY HIGH temperatures
and can cause severe burns if touched.
Even after the gas is turned off, fireplace
surfaces remain extremely hot.
WARNING
The door should easily close
without needing to be pressed
down. If it has to be pressed
down to close, the gasket in the
top of the door should be dressed
so it lays on the glass.
