background image

41

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Care and Operation

900358-00, 01/2018

Innovative Hearth Products
DRT63STTYN Power-Vent 

 Figure 57: SIT Proflame Gas Valve

Remote Control System

The Remote Control System allows you to com-

mand the functions of your fireplace from the 

comfort of your chair.  It is configured to control 

the On/Off primary burner operation and flame 

levels (through six levels) and provide On/Off 

and Smart control of this appliance.

The receiver connects directly to the gas valve, 

stepper motor with and umbilical cord wiring 

harness (see wiring diagram on 

Page 44

)

.

The Receiver is powered by 4 AA type batteries, 

located within.

The Receiver accepts commands via radio 

frequency from the Transmitter and does not 

require line-of-sight operation.  

The Receiver three-position slider switch can 

be set to one of three positions: ON (Manual 

Override), REMOTE (Remote Control), or OFF.

Initializing the System for the First Time

Install the 4 AA batteries into the receiver bat-

tery bay (behind the wall switch plate).

NOTE:

  Install the batteries into the battery bay 

as indicated on the battery cover.  Ensure that 

batteries are installed with proper polarity (+/-).

Place the three-position slider switch in the 

"Remote" position (

see

 

Figure 58, next page

)

.  

Using the end of a paper clip, or other similar 

object, insert the end of the paper clip into 

the hole marked “PRG” on the Receiver front 

cover.  The Receiver will "beep" three (3) times 

to indicate that it is ready to synchronize with 

a Transmitter.  

CAUTION:  Property damage hazard.  Ex-

cessive heat can cause property damage.  

The appliance can stay lit for many hours.  

Turn off the appliance if it is not going to 

be attended for any length of time.  Always 

place the Transmitter where children can 

not reach it.

Temperature Indicator Display

With the system in the "OFF" position, press 

the Room Temperature Key and the Mode Key 

at the same time (

see 

Figure 59, next page

)

.  

Look at the LCD screen on the Transmitter to 

verify that a C or F is visible to the right of the 

Room Temperature display (

see 

Figure 60, 

next page

)

.

Turn ON the Appliance

With the receiver switch in the "Remote" posi-

tion, press the ON/OFF Key on the Transmitter. 

The Transmitter display will show all active 

icons on the screen. At the same time, the 

Receiver connects to the gas valve coil and 

the appliance main burner turns on. A single 

"beep" from the Receiver will confirm reception 

of the command.

Turn OFF the Appliance

Press the ON/OFF Key on the Transmitter. The 

Transmitter LCD display will only show the 

room temperature and Icon. At the same time, 

the Receiver disconnects the gas valve coil 

and the appliance burner turns off. A single 

"beep" from the Receiver confirms reception 

of the command.

Remote Flame Control

The system has six (6) flame levels. See 

Figure 61 (next page) 

for an example. With 

the system on, and the flame level at the 

maximum in the appliance, pressing the 

DOWN Arrow Key once will reduce the flame 

height by one step until the flame is turned off.
The UP Arrow Key will increase the flame height 

each time it is pressed.  If the Up Arrow Key is 

pressed while the system is on but the flame is 

off, the flame will come on in the high position 

(

see 

Figure 62, next page

)

.  A single "beep will 

confirm reception of the command.

Install the 3 AAA type batteries in the Trans-

mitter battery bay, located on the base of the 

Transmitter.  With the batteries already installed 

in the Transmitter, push the ON button.  The 

Receiver will "beep" four times to indicate the 

Transmitter's command is accepted and sets 

to the particular code of that Transmitter.  The  

system is now initialized.

Low Battery Power Detection

The life span of the Receiver batteries depends 

on various factors:  quality of the batteries used, 

the number of ignitions of the appliance, the 

number of changes to the room temperature 

set point, etc.

When the Receiver batteries are low, no "beep" 

will be emitted from the Receiver when it receives 

an ON/OFF command from the Transmitter.  This 

is an alert for a low battery condition for the 

Receiver.  When the batteries are replaced the 

"beep" will be emitted from the Receiver when 

the ON/OFF key is pressed (See “Initializing the 

System for the First Time,” 

at left

).

When the transmitter batteries are low, a bat-

tery icon will appear on the LCD display of the 

transmitter before all battery power is lost.  

When the batteries are replaced this icon will 

disappear.

       WARNING 

Fire Hazard. Risk of severe injury 

or death. The Receiver causes 

ignition of the appliance. The 

appliance can turn on suddenly. 

Keep away from the appliance 

burner when operating the 

Remote Control System or when 

activating manual bypass of the 

Remote Control System.

Wire

(From DFC Wire 

Harness)

Pressure 

Regulator 

Tower

Yellow Ground Wire

(From DFC Wire 

Harness)

Green Wire

(From DFC Wire 

Harness)

Inlet (In) Test Port

Manifold (Out) 

Test Port

Connect GTMS 

Wire Harness

Main Gas Inlet 

3/8" NPT

Содержание DRT63































































Отзывы: