Super Products Camel 1200 (Dump Body) Скачать руководство пользователя

Страница: 142 / 158

7-10

Publication: 0028607

TROUBLESHOOTING

Hydraulics

No main hydraulic oil
pressure

Work mode not enabled,
still in road mode

Enable work mode.

Hydraulic pump not
engaged

Shift the transmission into D drive;
transmission controller will show 6-4.

Air solenoid not getting a
signal

Locate the signal problem; repair or
replace faulty components.
See Table 7-1: Mechanical
Troubleshooting.

Transfer case will not
engage

Chassis air pressure too
low

Run engine until air pressure reaches
100 psi.

Shift MODE rocker switch to ROAD
and back to WORK.

Boom, hose reel, and
body functions not
moving

Hydraulic valve fouled
with debris

• Shift the hydraulic valve using the

manual override. This may free
the fouled valve. A dirty cartridge
valve may need to be cleaned or
replaced.

• Change the hydraulic filter.

Directional valve not
controlling the function

• Set the manual override on the

associated proportional valve by
turning the screw inward, starting
at about 25%.

• If the directional solenoid LEDs

are lit and the function moves, the
directional valve and coil are
good.

• If the directional solenoid LEDs

are not lit and if using manual
directional overrides moves the
function, the directional valves are
good.

• If the function does not work

using the directional valve
overrides, the directional or
proportional valve may have
failed.

Failed directional or
proportional valve

Connect pressure gauge to manifold
port and check for pressure.

Hydraulic valve fouled
with debris

See Table 7-1: Mechanical
Troubleshooting.

LED on solenoid
connector or I/O module
not lit when function is
enabled

• Verify that the proper mode is

selected for the desired function.

• Locate and repair or replace.

Table 7-2: Electrical Troubleshooting (Continued)

Function

Symptom

Probable Cause

Solution

Содержание Camel 1200 (Dump Body)































































































































































Результаты поиска

Содержание Camel 1200 (Dump Body)

Отзывы:

Похожие инструкции для Camel 1200 (Dump Body)

Бренды по названию

Популярные бренды

Super Products Camel 1200 (Dump Body), Руководство оператора

Результаты поиска

Содержание Camel 1200 (Dump Body)

Отзывы:

Похожие инструкции для Camel 1200 (Dump Body)

Бренды по названию

Популярные бренды