Super Products Camel 1200 (Dump Body) Скачать руководство пользователя

Страница: 134 / 158

7-2

Publication: 0028607

TROUBLESHOOTING

Mechanical Troubleshooting

Table 7-1: Mechanical Troubleshooting

Function

Symptom

Probable Cause

Solution

Road mode:
starting truck

Engine will not start when
in road mode

Engine problems

Have engine mechanic check for
problems.

Emergency stop

Engine will start but all
functions will not operate

Emergency stop switch
pushed at front panel or
curbside panel

Reset the emergency stop switch by
twisting the knob.

Emergency stop
on remote
pendants

Vent door opens and
engine RPM drops to idle

Pendant emergency stop
button depressed

Clear emergency stop mode by
resetting the emergency stop button –
turn the pendant OFF then back to
ON and then all the way to SHIFT.

Emergency stop
message displayed on
the front control panel
HMI screen

Wireless pendant
batteries are dead

Replace the wireless pendant
batteries.

All functions do not work

Receiver power lost

See Table 7-2: Electrical
Troubleshooting.

Control system

Control system not
turning on

Main fuse blown

See Table 7-2: Electrical
Troubleshooting.

Ignition enable signal
failed.

Throttle control

Engine RPM will not
increase or decrease

Engine speed dial
advanced too far

Turn dial back to zero and then turn it
back up.

Emergency stop is
enabled on pendant

• Mute the emergency stop alarm at

the display until situation is
corrected.

• See “Emergency stop” function in

this table.

Hydraulics

No main hydraulic oil
pressure

Work mode not enabled,
still in road mode

Enable work mode.

Hydraulic pump not
engaged

The transfer case has not shifted out
of road mode, and the rear axle has
not disengaged.
See “Transfer case will not engage”
symptom in this section.

Supply valve closed

Open the hydraulic supply valve.

Low oil level in hydraulic
reservoir

Add oil as required.
Check for leaks.

Oil pump suction line
plugged or hose liner
collapsed (very rare)

Repair or replace as required.

Air solenoid not getting a
signal

See Table 7-2: Electrical
Troubleshooting.

Transfer case will not
engage

Chassis air pressure too
low

Run engine until air pressure reaches
100 psi.

Cycle the cab MODE rocker switch to
ROAD and back to WORK.

Содержание Camel 1200 (Dump Body)































































































































































Результаты поиска

Содержание Camel 1200 (Dump Body)

Отзывы:

Похожие инструкции для Camel 1200 (Dump Body)

Бренды по названию

Популярные бренды

Super Products Camel 1200 (Dump Body), Руководство оператора

Результаты поиска

Содержание Camel 1200 (Dump Body)

Отзывы:

Похожие инструкции для Camel 1200 (Dump Body)

Бренды по названию

Популярные бренды