Super Products Camel 1200 (Dump Body) Скачать руководство пользователя

Страница: 137 / 158

TROUBLESHOOTING

Publication: 0028607

7-5

Vacuum system
(Continued)

Vacuum pump does not
draw full vacuum

Holes worn in vac hose or
dig tube

Repair or replace as required.

Hose coupler assembly
gasket(s) missing or
damaged

Adjust, repair, or replace any missing
or leaking gaskets.

Gasket from inspection
door missing or damaged

Repair or replace gasket.

Tailgate gasket damaged
or not sealing

Filter housing door seals
damaged or not sealing

Repair or replace seal.

Hose between filter and
cyclone separator
damaged or not sealing

Repair or replace hose.

Hose between
make-break and boom
cannon damaged or not
sealing

Vacuum pump

Dust in vacuum pump
discharge

Note: Operating the
vacuum system while this
condition exists could
cause significant damage
to vacuum pump and void
your warranty.

Missing or damaged filter

Replace filter.

Filter not sealing properly

Vacuum vent
door

Vacuum vent door will not
function

Vacuum pump not
engaged

Enable WORK and VAC modes.

Vacuum relief valve open
due to debris level sensor
sensing a full load

Dump the load.

Lack of chassis air
pressure to operate vent
door

Check chassis air pressure. Run
engine until pressure rises.

Air solenoid failure

See Table 7-2: Electrical
Troubleshooting.

Electric signal not present

Vacuum RPM

Vacuum pump RPM not
displayed

Failed speed sensor on
transfer case

• Replace speed sensor.

• See Table 7-2: Electrical

Troubleshooting.

Table 7-1: Mechanical Troubleshooting (Continued)

Function

Symptom

Probable Cause

Solution

Содержание Camel 1200 (Dump Body)































































































































































Результаты поиска

Содержание Camel 1200 (Dump Body)

Отзывы:

Похожие инструкции для Camel 1200 (Dump Body)

Бренды по названию

Популярные бренды

Super Products Camel 1200 (Dump Body), Руководство оператора

Результаты поиска

Содержание Camel 1200 (Dump Body)

Отзывы:

Похожие инструкции для Camel 1200 (Dump Body)

Бренды по названию

Популярные бренды