background image

 

 

cooling, we recommend our selection of various accessories which reduce or prevent entry of warm air into 
the room, or via the remote control. 
 
Using the „Comfort Control- S Kit“ you can also control the TRANSFORM unit from inside using the remote 
control. 

 

Note: After switching on, or over, the ventilator operates, but the compressor only starts after the control lamp has flashed for 3 

minutes. Cooling effect may require a further 10 minutes. Further information is available under the part „Troubleshooting“.  

 

HEATING 
 

 

On cold days it is recommendable to start the TRANSFORM unit early in order to get a warm room. 

 

For the heating function and to improve the heating effect and avoid lower temperatures (lower than  

17°C) we recommend you remove the rubber plug from  the condensation water outlet and allow the 
condensation water to leak out of the TRANSFORM unit using the drainage hose. However, the drainage 
hose does not have to be connected in the heating mode. Please make sure that the condensation water 
outlet is closed with the rubber cap during operation. In such a case, proceed analogously to the emptying 
of the water tank in the cooling function. 

 

The heating function of the TRANSFORM unit must not be operated at a room temperature of more 

than 23°C or less than 7°C. The TRANSFORM unit can  also be operated with heating function, if the 
outside temperature is lower than 7°C. However, you  must then ensure that the TRANSFORM unit is 
operated inside and the room temperature is at least 7°C. 

 
  

 

 
 
 

 
 
HEATING IN INDOOR OPERATION  
The TRANSFORM unit is in the room to be heated.  
Connect the air hose and the air outlet grid to the TRANSFORM unit as displayed in the illustration; the air 
hose connection piece and air outlet grid need to be exchanged. 
 
 
 
 
 
 
 
 
 
 
 
The cold extract air has to be led out of the room via the air hose. This can be executed e.g. via a tilted 
window, a door or wall aperture. Make sure that no cold outside air can enter the room. For effective 
heating, we recommend our selection of various accessories which reduce or prevent entry of cold air into 
the room.  
 
Set the function to „Heating“. The settable temperature range is between 15°C and 25°C target 
temperature. You can set this using the temperature control. 

 

Note: After switching on, or over, the ventilator operates, but the compressor only starts after the control lamp has flashed for three 

minutes. Cooling effect may require a further 10 minutes. Further information is available under the part „Troubleshooting“.  

 
 
 
 
 
 
 
 
 
 

Caution: In the heating mode, separate setting of the ventilator is not provided, since the highest 
ventilation level is already preset to avoid overheating of the unit. 

Содержание Klimatronic Transform 10500














Отзывы: